WidenersRotoMetals2Titan ReloadingADvertise here
RepackboxInline FabricationMidSouth Shooters SupplyLee Precision

  • mnewcomb59's Avatar
    03-31-2020, 08:50 PM
    I like 2.9 gr Titegroup and have used up to 4.4 gr Power Pistol with the Lee 158-rf at 1.07". https://www.shootingtimes.com/editorial/reloading-heavy-bullets-in-9mm-luger/99514
    25 replies | 14404 view(s)
  • mnewcomb59's Avatar
    03-21-2020, 10:27 PM
    This is generally what I have seen too, this is why I asked in the OP "Do the heavier bullets shoot higher like you would expect? I saw one guy say his Lee 300 hits lower than the Lee 255 at 50 yards." I am more interested in zeroing for...
    11 replies | 594 view(s)
  • mnewcomb59's Avatar
    03-21-2020, 09:47 AM
    I made it to the range last weekend. I found that 250s around 1000 fps shot dramatically different at 50 yards compared to all other loads tried. With my tall front sight, I could zero the subsonics but all other loads were 4-8 inches low. 250s...
    11 replies | 594 view(s)
  • mnewcomb59's Avatar
    03-21-2020, 09:26 AM
    I once had a Rossi 92 357 that took 12 pieces of scotch tape on the rim before the lever wouldnt close. I has ruining 38 special cases on first firing, and a small percent of factory and reload 357s would have case separations after firing or during...
    11 replies | 698 view(s)
  • mnewcomb59's Avatar
    03-20-2020, 02:46 PM
    With a bottom pour pot ad 2 to 6 cavity molds, my good consistent weight bullets come only when the mold is run like a robot. I do not keep any bullets cast before I have a 3 second liquid sprue. At my rate of casting, if the sprue starts...
    32 replies | 1241 view(s)
  • mnewcomb59's Avatar
    03-19-2020, 09:00 AM
    I have had 3 or 4 Rossi 92s in 357 and they were all 4 MOA guns or better with open sights. Every gun would shoot 10 shots around an inch at 50 yards. At 100 yards every gun would shoot 10 shots under 4 inches. Open sights are harder to shoot but...
    26 replies | 1264 view(s)
  • mnewcomb59's Avatar
    03-13-2020, 07:40 PM
    You need your tin equal or greater than the percentage of antimony. 3-3-94 is a much better alloy than 2-3-95 (ww +2% tin). When every antimony molecule has a tin molecule to bond with, they will bond and the alloy becomes much more ductile. You...
    21 replies | 2685 view(s)
  • mnewcomb59's Avatar
    03-09-2020, 08:56 PM
    Nice stuff oldhenry! Depending on how recently those were cast, they may age harden some. With my 850 fps 250 grain 45 colt loads using 2-2-96 air cooled, the bullets mushroomed two weeks after cast and 2 months after cast they only swelled up...
    17 replies | 820 view(s)
No More Results
About mnewcomb59

Basic Information

Statistics


Total Posts
Total Posts
178
Posts Per Day
0.07
General Information
Last Activity
Yesterday 04:07 PM
Join Date
06-12-2013
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check