Titan ReloadingLee PrecisionMidSouth Shooters SupplyInline Fabrication
RepackboxADvertise hereWidenersRotoMetals2

Donate Now Goal amount for this year: 6000 USD, Received: 3655 USD (61%)
Our Annual server fund drive is going on now! This donation drive helps fund Cast Boolits for an entire year, and helps support our 2nd amendment rights! You can donate by Paypal by clicking the DONATE button. Or by Cash / Check / MO to the address below:

Willy Snyder
PO Box 2732
Pocatello, ID 83206
****Due to overwhelming e-mails, I will be very slow in updating this list. Please bear with me!****


Tab Content
  • Outpost75's Avatar
    Today, 07:23 AM
    Outpost75 replied to a thread Long term storage in Our Town
    LPS3 or LPS4 are both very good, as is also Break Free Collector. Lacking either of those, Lee Liquid Alox bullet lube, diluted with equal parts of diesel, Jet-A, JP8 or kerosene works well applied with a paint brush and worked into all surfaces. ...
    12 replies | 254 view(s)
  • Outpost75's Avatar
    Today, 07:10 AM
    At kitchen garden ranges within 50 yards, a 250-grain or heavier .45 cal. bullet, of soft lead, such as 1 to 40 tin-lead, having a meplat of 0.6 of the bullet diameter or larger, which hits the deer at 800 fps or more, will shoot clear through the...
    10 replies | 197 view(s)
  • Outpost75's Avatar
    Today, 07:00 AM
    I want to be able to shoot deer in my garden in early morning hours without disturbing the neighbors. Firing a blunt, heavy .45 bullet at 800 fps from a rifle does that without needing a "can" and you can eat right up to the bullet hole.
    14 replies | 163 view(s)
  • Outpost75's Avatar
    Yesterday, 07:02 PM
    Current issue of The Fouling Shot has pressure tested data from Larry Gibson for .44 Magnum and .44-40 with current powders. If anyone would like a copy PM me with an email address which will accept a 2MB .pdf attachment.
    12 replies | 1330 view(s)
  • Outpost75's Avatar
    Yesterday, 05:09 PM
    I can tell you from experience that the Crispy Creme doughnuts work. We used to trap nuisance bears to tag, put radio collars on and relocate them to the most remote part of the state. If they returned they would be shot. Doughnut waste from...
    12 replies | 192 view(s)
  • Outpost75's Avatar
    Yesterday, 02:36 PM
    He would be much better off with a 12-ga. pump shotgun. The Judge is a sub-par performer in .45 Colt and a poor performer in .410. He would be better off carrying a rucksack full of Crispy-Creme doughnuts to throw at and distract the bear and...
    12 replies | 192 view(s)
  • Outpost75's Avatar
    Yesterday, 02:22 PM
    The factory open sights of the pre-1964 Winchester Model 94 in .30-30 came zeroed to strike within a 3 inch circle drawn tangent at 6:00 inside a 6 inch black aiming bull at 50 yards. The normal sight picture with open sights is to take a...
    15 replies | 184 view(s)
  • Outpost75's Avatar
    Yesterday, 01:25 PM
    Not a pretty picture! Expect criminal charges to be forthcoming and IRS to revoke tax-exempt status just for starters. ...
    35 replies | 644 view(s)
  • Outpost75's Avatar
    Yesterday, 11:16 AM
    The 1.315" length is max. 1.305 is the trim-to length which new R-P or W-W brass would usually be. Due to the heavy crimp applied to obtain acceptable ballistic uniformity with 100-grain softpoint bullets cases fired in factory loads WILL stretch...
    10 replies | 294 view(s)
  • Outpost75's Avatar
    Yesterday, 11:07 AM
    I've mostly run Bullseye or 452AA (until it was discontinued in 1991) and since then mostly WST in the Star machines all total for over 50 years. I prefer a fast-burning powder which attains the desired velocity with a clean burn at the lowest...
    20 replies | 299 view(s)
  • Outpost75's Avatar
    08-05-2020, 08:00 PM
    Colt letter says was shipped to Belknap Hardware Company, Louisville, KY April 6, 1905 as purchasing agent for Baldwin Phelps Detective Agency. Is a documented West Virginia Coal Wars Gun captured by my great grandfather during the Battle of Blair...
    19 replies | 333 view(s)
  • Outpost75's Avatar
    08-05-2020, 07:16 PM
    My favorite recreational loads for the .44 Magnum use the Accurate 43-206H "stump-nosed" SWC, which weighs 213-grains in 1 to 30 tin-lead, with 7.5 grains of Bullseye. I load 6 grains of Bullseye with the same bullet in the .44 Special or .44-40...
    19 replies | 333 view(s)
  • Outpost75's Avatar
    08-05-2020, 07:00 PM
    Given the finer particle size of 4Fg compared to larger granulation, a greater percentage by weight is composed of graphite, and while the burning rate is faster, the total energy produced in ft.-lbs. per grain is less. Larry's pressure test in .45...
    18 replies | 298 view(s)
  • Outpost75's Avatar
    08-05-2020, 03:29 PM
    My .45 ACP Model 625 of 1989 had the etched rifling and leaded incessantly and resisted all attempts to lap or otherwise smooth the barrel, so I sold it.
    18 replies | 407 view(s)
  • Outpost75's Avatar
    08-05-2020, 11:24 AM
    With 1.305" case, the 0.3" nose length of Accurate 31-105T results in a 1.605" overall cartridge length, whereas factory max for .32-20 is 1.592". If this is an issue, when you order the mold ask Tom to shorten the nose length by 0.015" to .285"...
    10 replies | 294 view(s)
  • Outpost75's Avatar
    08-04-2020, 11:36 PM
    We load 1000's of rounds of .30-'06 gallery loads annually for use in club 03A3s for Appleseed classes. We use a Dillon machine set up to meter 8.5 grains of WST shotshell powder and we load Accurate 31-155D cast from backstop scrap, loaded as-cast...
    34 replies | 1308 view(s)
  • Outpost75's Avatar
    08-04-2020, 02:08 PM
    SAAMI Max. Average Pressure is the statistical maximum individual pressure, or the maximum sample average (machine loading limit) plus 3 standard deviations. The proof pressure is ordinarily 1.25 times the MAP, which varies according to the...
    7 replies | 377 view(s)
  • Outpost75's Avatar
    08-04-2020, 01:47 PM
    Indian Joe is correct on the RCBS bullet. However, my experience with both my 1905 Colt Frontier Six Shooter and 1920 Colt New Service is that they impact low relative to the sights when firing the lighter 200-grain bullets. To avoid having to cut...
    23 replies | 1187 view(s)
  • Outpost75's Avatar
    08-04-2020, 01:05 PM
    OOPS! Thanks for the correction. 4Fg is not ideal, but will "work," loosely filling the case, without compression.
    18 replies | 298 view(s)
  • Outpost75's Avatar
    08-04-2020, 12:06 PM
    2Fg will work as long as you fill the case, settle the charge for maximum powder capacity and obtain at least 3mm of powder compression with the bullet seated.
    18 replies | 298 view(s)
  • Outpost75's Avatar
    08-04-2020, 10:56 AM
    Accurate 31-105T is very close to original factory .32-20 lead bullets.
    10 replies | 294 view(s)
  • Outpost75's Avatar
    08-04-2020, 10:54 AM
    Two lighter-weight Accurate bulets for .32 ACP which feed well in finicky pistols which tend to bobble with anything other than FMJ hardball. The 31-075H has a .303 diameter nose above the front driving band for tight chambers with short...
    15 replies | 340 view(s)
  • Outpost75's Avatar
    08-03-2020, 08:21 PM
    What is sold in the US as aliphatic mineral spirits or Stoddard Solvent is a nonflammable "safety solvent" used for dry cleaning, which does not contain volatile organics and such does not ignite when tested under the NFPA test standard, such that...
    26 replies | 5158 view(s)
  • Outpost75's Avatar
    08-02-2020, 05:38 PM
    Jacketed bullets for the .32 Winchester Special run .320" and have a thin jacket and soft core to squeeze down easily. The same bullet is factory loaded in US 8mm sporting ammunition in a mild charge which is safe for the 1888 Commission rifles. I...
    13 replies | 238 view(s)
  • Outpost75's Avatar
    08-02-2020, 12:01 PM
    To produce a correct roll crimp for revolver use, get a .45 Auto Rim die set and simply use a .45 Colt shell holder. A pleasant and accurate load which produces less than 14,000 psi is 3.5 grains of Bullseye or TiteGroup, or 4 grains of WST or 231...
    11 replies | 293 view(s)
  • Outpost75's Avatar
    08-01-2020, 07:35 PM
    I own two S&W 940s. The first one went 1500 rounds of standard-pressure 9mm before developing more than 0.002" of end-shake. The crane arbor was stretched, the gun tightened up and in another 1500 rounds it needed to be tightened again, by that...
    191 replies | 36254 view(s)
More Activity

Statistics


Total Posts
Total Posts
8,248
Posts Per Day
3.14
General Information
Join Date
05-31-2013
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check