Inline FabricationMidSouth Shooters SupplyRotoMetals2Graf & Sons
StainLess Steel MediaLee PrecisionRepackboxWideners
Titan Reloading
  • sghart3578's Avatar
    Yesterday, 11:08 PM
    I gotta say, this thread is disheartening for me. I have been saving for a nice lever action, sold some stuff, etc. and I have always wanted an 1873. I was leaning toward the Uberti. I was going to choose the 45 Colt as I don't load for the...
    15 replies | 477 view(s)
  • sghart3578's Avatar
    10-07-2018, 02:37 PM
    I have always heard this also. I may have to break down and buy one.
    15 replies | 289 view(s)
  • sghart3578's Avatar
    10-06-2018, 05:58 PM
    I don't own a Uberti (yet) but I have always had excellent results with the Lee 452-255-RF mold. In my Rossi, Marlin (that I sold) and my Vaquero and Blackhawk I shoot these bullets as cast with no sizing, one very light coat of BLL. This...
    15 replies | 289 view(s)
  • sghart3578's Avatar
    10-04-2018, 12:52 AM
    My Marlin needed .454" bullets for best performance. I ended up shooting those in my Vaquero and Blackhawk also. Are you sure about the twist rate on the Marlin? If so then I may have to look into one of those.
    4 replies | 203 view(s)
  • sghart3578's Avatar
    10-03-2018, 10:54 PM
    If you have one of the affected rifles, like I did, contact Lyman via email. They will send you a shipping tube with packing material, etc. to return just the barrel. They ask that you remove the sights, pack up the barrel and send it back. In...
    13 replies | 541 view(s)
  • sghart3578's Avatar
    10-02-2018, 09:48 PM
    I'm happy to hear that you liked your new Marlin. I also have one of the new 1894C's and I couldn't be happier. It looks good and is very accurate. Steve in N CA
    6 replies | 342 view(s)
  • sghart3578's Avatar
    09-27-2018, 06:15 PM
    Outstanding! I am glad to hear this. I have two new 2018 built Marlins in my safe, one in 357 mag and one in 45-70. I couldn't be happier with them. Keep up the good work. Steve in N CA
    9 replies | 301 view(s)
  • sghart3578's Avatar
    09-27-2018, 07:51 AM
    bump....
    7 replies | 763 view(s)
  • sghart3578's Avatar
    09-26-2018, 07:01 AM
    sghart3578 replied to a thread New Miroku 1873 in Leverguns
    Very nice!
    17 replies | 729 view(s)
  • sghart3578's Avatar
    09-26-2018, 07:00 AM
    sghart3578 replied to a thread Big Bore Regret..? in Leverguns
    In my 1895CB I have settled on the Lee 405, beagled, sized to .459" and lubed with Randy's Tac-X. I load them over 11 gr of Unique. Easy on the gun, easy on the shoulder, and puts them into a small group at 100 yards.
    40 replies | 1583 view(s)
  • sghart3578's Avatar
    09-26-2018, 06:53 AM
    I use alox in rifle loads up to 1800 fps and have had no leading. I only use one very light coat on well fitting, gas checked bullets in 3 or 4 calibers. In plain-based rifle bullets I load to 1400 fps with no problems. The 1800 fps is by no...
    6 replies | 636 view(s)
  • sghart3578's Avatar
    09-26-2018, 06:47 AM
    sghart3578 replied to a thread xlox in Boolit Lube !
    I second what ShooterAZ said. Bullet fit is first. No lube will help you if the bullets are undersized. Then a very, VERY light coat of alox. For 38 cal bullets I use about 1/2 teaspoon per 100 bullets. And I also thin my alox with a...
    5 replies | 303 view(s)
  • sghart3578's Avatar
    09-26-2018, 12:01 AM
    Hello, I have a RCBS Turret Press for sale in very good shape. It comes with 4 turrets total. Somewhere I have the primer tubes and other parts. I will find them in my shed. I don't use them as I prime off the press. I would like to get...
    7 replies | 763 view(s)
  • sghart3578's Avatar
    09-25-2018, 06:26 PM
    Maybe, But almost every deer I have ever taken was from some kind of support. Either a log, the hood of a truck, etc. Only one was taken standing un-supported. He stepped out 35 yards away. Not exactly challenging, even for me. And you...
    28 replies | 1035 view(s)
  • sghart3578's Avatar
    09-20-2018, 10:40 AM
    sghart3578 replied to a thread 30-30 load request in Leverguns
    While I can't necessarily help with your jacketed loads, my best accuracy for my 150gr and 170gr loads with cast comes from IMR 3031. A close second has been H4895.
    29 replies | 1151 view(s)
No More Results
About sghart3578

Basic Information

About sghart3578
Location:
Northern California

Statistics


Total Posts
Total Posts
637
Posts Per Day
0.32
General Information
Last Activity
Today 09:16 AM
Join Date
04-06-2013
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check