RotoMetals2WidenersADvertise hereTitan Reloading
Inline FabricationMidSouth Shooters SupplyLee PrecisionRepackbox

  • shell70634's Avatar
    06-03-2020, 10:09 PM
    Make sure the ejector rod hasn't un screwed a bit too.
    13 replies | 308 view(s)
  • clodhopper's Avatar
    06-03-2020, 12:41 AM
    clodhopper replied to a thread Core molds in Swaging
    The paper gives .0015 fudge room on both sides of center. So if your hole is off center just a little bit, the casting will still fall out of the mold. When you remove the paper the cavity is reduced in volume.
    10 replies | 672 view(s)
  • shell70634's Avatar
    06-02-2020, 06:24 PM
    #03. Not packaged but appears unused. #18. New in package #10. New in package #6. New in package All for $50.00 shipped. Will take cash, money order, PP F&F, or prime rib.
    1 replies | 104 view(s)
  • clodhopper's Avatar
    06-01-2020, 11:22 PM
    clodhopper replied to a thread Core molds in Swaging
    You could drill holes ok, but if the holes are not centered on the parting line of the blocks the cores do not want to fall out. Don't mount the blocks on the handles until after drilling the cavities. The fasteners are cleverly designed to not...
    10 replies | 672 view(s)
  • clodhopper's Avatar
    06-01-2020, 08:43 PM
    clodhopper replied to a thread Core molds in Swaging
    Charts for calculating weight of cores are here. www.castboolits.gunloads.com/showthread.php?276943-A-Little-Math-That-Will-HOPEFULLY-Be-Helpful Post #8 is where Gitano helped a lot. You still have to do some math. I have cut a few core molds on...
    10 replies | 672 view(s)
  • shell70634's Avatar
    06-01-2020, 03:25 PM
    I'll take em. PM to follow. Shelly
    1 replies | 148 view(s)
  • clodhopper's Avatar
    05-24-2020, 11:07 PM
    This question comes up so often. Brass is a little harder than copper, but compared to steel, brass is soft. Hot copper is sticky, but the addition of zinc makes brass comparatively slick. Most bullets are jacketed with gilding metal, which...
    13 replies | 1223 view(s)
  • shell70634's Avatar
    05-19-2020, 07:35 PM
    Before posting any pics I open them with the Paint program on my computer and resize them. Most from my phone are 4000 x 3000 or so pixels. I resize to 1000 or less, then crop, then save. They load up much quicker for me. I'm not computer...
    3 replies | 819 view(s)
  • clodhopper's Avatar
    05-16-2020, 06:23 PM
    Good looking bullets.
    13 replies | 1223 view(s)
  • shell70634's Avatar
    05-16-2020, 01:03 PM
    My daughter had 20 or so stolen in east Texas about 5 years ago. They've gotten 5 or 6 back. One from Ohio. The SO gave them back within a couple days of receiving them. Still looking for the rest.
    68 replies | 1923 view(s)
  • clodhopper's Avatar
    05-14-2020, 11:47 PM
    clodhopper replied to a thread Joining an airgun forum in AirGuns
    Bob Strene is on many forums, even castboolits.gunloads.com
    12 replies | 2138 view(s)
  • clodhopper's Avatar
    05-13-2020, 03:50 PM
    I was using a lyman big dipper until the heating coil burned out. Strongly considering Turning some scrap aluminum to fit tight, and fill the bottom half of the pot.
    21 replies | 773 view(s)
  • shell70634's Avatar
    05-11-2020, 04:19 PM
    I'll take it. PM follows Shelly
    1 replies | 666 view(s)
No More Results
About shell70634

Basic Information

About shell70634
Location:
SW Louisiana
Occupation:
LEO/Bomb Tech RETIRED!!!

Signature


"EXPERT= Ex is a has been, spurt is a drip under pressure" Unknown

Statistics


Total Posts
Total Posts
191
Posts Per Day
0.07
General Information
Last Activity
Today 12:01 PM
Join Date
04-01-2013
Referrals
0

3 Friends

  1. clodhopper clodhopper is offline

    Boolit Master

    clodhopper
  2. Nebulous Nebulous is offline

    Boolit Mold

    Nebulous
  3. waarp8nt waarp8nt is offline

    Boolit Buddy

    waarp8nt
Showing Friends 1 to 3 of 3
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check