RotoMetals2WidenersInline FabricationLee Precision
MidSouth Shooters SupplyStainLess Steel MediaTitan ReloadingGraf & Sons

  • shell70634's Avatar
    Yesterday, 08:59 PM
    These were in a box of bullet master parts but I don't think they belong. Might some kind of temperature switch or sensor. They're about 4x10 inches. Both are exactly alike.
    2 replies | 153 view(s)
  • shell70634's Avatar
    Yesterday, 02:44 PM
    shell70634 replied to a thread Bullet Master in Casting Equipment
    Got it running. Casts great. Now I have to automate my sizer. Bought 5 more sets of molds at a great price. Once I figure out which I like best will probably sell the rest. Have decided to repair the spare one for a friend. Only need pot and...
    6 replies | 412 view(s)
  • waarp8nt's Avatar
    09-21-2018, 02:28 PM
    Thanks!!! I have one on the way.
    2 replies | 131 view(s)
  • waarp8nt's Avatar
    09-20-2018, 09:40 PM
    Looking for a good used / like new or new copy of the Book "Firearm Blueing and Browning" by R.H. Angier Track of the Wolf is currently out and online auctions are way overpriced. Post or PM if you have a copy.
    2 replies | 131 view(s)
  • shell70634's Avatar
    09-14-2018, 10:51 AM
    #3 Blued SSK Contender 14" 45/70 pistol barrel, 6screw TSOB base, drilled and tapped for front sight (not included) another one I bought used and haven't fired, it is a used barrel with normal wear/handling marks, some blue wear at the muzzle and...
    8 replies | 838 view(s)
  • clodhopper's Avatar
    09-14-2018, 12:58 AM
    clodhopper replied to a thread Swage die reamer in Swaging
    Nice cutter Bill, I have this set of collet blocks, but have not used it yet making reamers. https://www.ebay.com/i/112194207638?chn=ps And a set of 5C collets
    19 replies | 590 view(s)
  • waarp8nt's Avatar
    09-13-2018, 04:53 PM
    ^^^ My Dad's preferred method as well.
    20 replies | 691 view(s)
  • shell70634's Avatar
    09-07-2018, 11:42 AM
    I'll take em. PM headed your way. Shelly
    1 replies | 179 view(s)
  • clodhopper's Avatar
    09-06-2018, 09:41 AM
    clodhopper replied to a thread Swage die reamer in Swaging
    I have been moving to the same goal. It seems like the numbers are fuzzy. Starting with O-1 tool steel, you turn to say .308. With heat treating that diameter may change, pretty much have to try, and see what happens. So far I have built a radius...
    19 replies | 590 view(s)
  • clodhopper's Avatar
    09-02-2018, 07:25 PM
    A forum member PMed for more info. From sandbags it will shoot 1 1/2 -2 1/2 inches at 50 yards. with home made 185 grain jacketed bullets formed from 9mm cases. The bullets are formed in a .223 rem resizing die. then sized back down to .358 in a...
    248 replies | 82914 view(s)
  • clodhopper's Avatar
    09-02-2018, 08:41 AM
    Followed this thread for 8 years now. Voted yes today, bought a 77-357 several years ago. Yep it was pricey, sucks as a bench gun. When .22 long rifle was hard to get, this was my solution. A wonderful rifle for walking around making quick...
    248 replies | 82914 view(s)
  • clodhopper's Avatar
    08-31-2018, 09:17 AM
    These molds will be a great asset to the air gun industry. Suddenly a 30 cal springer could be in my future. I would pay handsomely for a 30 cal rifle incorporating mechanical recoil cancellation. Right now, a 22 caliber hunter mold would make...
    46 replies | 1388 view(s)
  • shell70634's Avatar
    08-30-2018, 07:42 AM
    If FISH4BUGS doesn't take it I will. Shelly
    3 replies | 352 view(s)
  • waarp8nt's Avatar
    08-27-2018, 04:41 PM
    Rich/WIS is a Straight Shooter with Good Communication & Super Fast Shipping!!! Thanks for the Hawken sight!
    14 replies | 2739 view(s)
  • waarp8nt's Avatar
    08-27-2018, 04:33 PM
    A good friend of mine bought a CVA Wolf for his daughter. I'm not sure the scope or load they use, but she consistently takes deer with it.
    8 replies | 368 view(s)
  • clodhopper's Avatar
    08-25-2018, 08:50 AM
    Most bullet sizing dies have an ejector pin on the end opposite where the bullet would go in. When you push a bullet into a die with enough force to change it's shape, it takes some push to overcome friction and vacuum to get the bullet back out of...
    3 replies | 346 view(s)
No More Results
About shell70634

Basic Information

About shell70634
Location:
SW Louisiana
Occupation:
LEO/Bomb Tech

Signature


“You only make one mistake in this business – you’re either an expert or you’re dead.”
Col. Thomas J. Kane

"EXPERT= Ex is a has been, spurt is a drip under pressure" Unknown

Statistics


Total Posts
Total Posts
110
Posts Per Day
0.05
General Information
Last Activity
Today 02:43 PM
Join Date
04-01-2013
Referrals
0

3 Friends

  1. clodhopper clodhopper is offline

    Boolit Master

    clodhopper
  2. Nebulous Nebulous is offline

    Boolit Mold

    Nebulous
  3. waarp8nt waarp8nt is offline

    Boolit Master

    waarp8nt
Showing Friends 1 to 3 of 3
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check