RotoMetals2Lee PrecisionRepackboxTitan Reloading
ADvertise hereInline FabricationWideners

  • clodhopper's Avatar
    02-13-2020, 10:00 AM
    clodhopper replied to a thread 25 cal pellet question in AirGuns
    Wally, seeing your are new to this forum, Working fast will be difficult if your pellets will not drop out of the mold. When cavities are cut the cutting tool leaves a tiny wire edge where the cavities meet. That little bit of metal makes the...
    13 replies | 784 view(s)
  • clodhopper's Avatar
    02-12-2020, 11:22 PM
    clodhopper replied to a thread Bleeding holes in Swaging
    If you want an ogive in wall of the die, it should be placed far enough in the longest conceivable core would be contained inside the die before you start forming. Your core will be smaller diameter than the slug, the curve of the ogive will...
    17 replies | 1394 view(s)
  • clodhopper's Avatar
    02-12-2020, 08:47 PM
    clodhopper replied to a thread Bleeding holes in Swaging
    That die looks like it should have close fitting punches at both ends. Both ends need sealed enough to get enough pressure to force lead out of the bleed holes. The base punch (at lest in my vison) would be domed to produce a dished base. The...
    17 replies | 1394 view(s)
  • shell70634's Avatar
    02-11-2020, 08:42 PM
    http://castboolits.gunloads.com/showthread.php?54524-Potter-melting-pot
    3 replies | 258 view(s)
  • clodhopper's Avatar
    02-11-2020, 10:04 AM
    clodhopper replied to a thread 25 cal pellet question in AirGuns
    Alfred has it nailed. Keeping the temp of the mold up is the key. Not so easy when you only pour a little dribble of lead in big blocks each cycle. Avoid drafts. Apply heat with a hot plate or other means. I sometimes use a piece of steel...
    13 replies | 784 view(s)
  • shell70634's Avatar
    02-10-2020, 06:12 PM
    I'LL take the star sizer PM to follow Shelly
    8 replies | 1006 view(s)
  • shell70634's Avatar
    02-10-2020, 03:45 PM
    Many years ago, in the piney woods of Fort Polk, we would shoot them from foxholes with M-16, a blank, and a section of cleaning rod. Wouldn't do it now, but it was great entertainment for young soldiers.
    102 replies | 4059 view(s)
  • clodhopper's Avatar
    02-10-2020, 10:15 AM
    Scopes that focus close in are rare. Tough inexpensive ones are even more rare. Thanks for letting everyone know.
    7 replies | 1262 view(s)
  • shell70634's Avatar
    02-09-2020, 05:05 PM
    In Louisiana at the end of the show, you're required to total your sales and pay local tax at the venue. Paperwork is provided to send the states share in by mail. Usually there's someone at the next table that will watch yours for a break and...
    23 replies | 1563 view(s)
  • shell70634's Avatar
    02-05-2020, 08:55 PM
    shell70634 replied to a thread WTS Hard lead in Swappin & Sellin
    I'll take two please. Thanx Shelly
    9 replies | 535 view(s)
  • shell70634's Avatar
    02-05-2020, 12:54 PM
    I believe the 338 Win Mag is the most popular and most common of the 338's. You might try The High Road or one of the long range shooting forums. Shelly
    22 replies | 1270 view(s)
  • clodhopper's Avatar
    02-04-2020, 01:02 AM
    I bought a 10-22 for a loaner rifle, took it out to the range one nice afternoon to sight it in. The trigger sucked. Gritty, like dragging the trigger over three bumps to fire. Was shooting prone, and had a nice comfy matt on top a piece of...
    11 replies | 395 view(s)
  • clodhopper's Avatar
    02-01-2020, 09:33 AM
    clodhopper replied to a thread Lead core problem in Swaging
    Lead has a known melting temperature. Adding tin lowers the melting temperature. Melt some of the suspect wire and check the temp.
    5 replies | 419 view(s)
  • clodhopper's Avatar
    01-30-2020, 07:29 PM
    clodhopper replied to a thread Lead core problem in Swaging
    Tin makes lead tough. Sometimes your die will break. If your die is 7/8-14 be careful.
    5 replies | 419 view(s)
  • clodhopper's Avatar
    01-27-2020, 11:34 PM
    I had on last week, bought two bricks, fired one box, one dud. Could not believe it, good strike by the firing pin, second strike on the opposite side did not fire either.
    15 replies | 721 view(s)
  • clodhopper's Avatar
    01-27-2020, 12:37 AM
    Here's an old post. Still making them in a .223 die. WWW.castboolits.gunloads.com/showthread.php?347930-357-advice They do not expand well. A .357 diameter hole serves just fine for my purposes.
    5 replies | 401 view(s)
No More Results
About shell70634

Basic Information

About shell70634
Location:
SW Louisiana
Occupation:
LEO/Bomb Tech RETIRED!!!

Signature


"EXPERT= Ex is a has been, spurt is a drip under pressure" Unknown

Statistics


Total Posts
Total Posts
177
Posts Per Day
0.07
General Information
Last Activity
Yesterday 04:46 PM
Join Date
04-01-2013
Referrals
0

3 Friends

  1. clodhopper clodhopper is offline

    Boolit Master

    clodhopper
  2. Nebulous Nebulous is offline

    Boolit Mold

    Nebulous
  3. waarp8nt waarp8nt is offline

    Boolit Buddy

    waarp8nt
Showing Friends 1 to 3 of 3
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check