RotoMetals2ADvertise hereMidSouth Shooters SupplyWideners
Lee PrecisionRepackboxInline FabricationTitan Reloading

Tab Content
  • Battis's Avatar
    04-06-2020, 12:45 AM
    In my collection of old ammo, I found a partial box of 32ACP and a partial box of 38-55 rounds. Notice the knurl (cool word) in the 38-55 case. I have no idea how old any of the rounds might be.
    24 replies | 447 view(s)
  • Battis's Avatar
    04-05-2020, 10:55 AM
    I have a Lee 32ACP seater die on the way that will crimp the case, and I ordered the Lee factory crimp die that you mentioned (Amazon - $16). Kinda like wearing a belt and suspenders. I even thought about removing the decapping pin from the S&W...
    24 replies | 447 view(s)
  • Battis's Avatar
    04-05-2020, 09:27 AM
    I read a review somewhere that said it didn't work on the 32ACP due to the case length, but if you have one, and it works, problem solved. I have the seating die on the way that should do the same thing. If the case headspaces on the semi-rim,...
    24 replies | 447 view(s)
  • Battis's Avatar
    04-04-2020, 10:13 PM
    I cut a case in half and sure enough, it headspaces on the semi-rim, though a full case, if too long, doesn't allow the rim to sit as it should. I trimmed 20 or so to the correct length, and they seat correctly. I also slugged the bore, something...
    24 replies | 447 view(s)
  • Battis's Avatar
    04-04-2020, 08:07 AM
    I found an old post on another forum where the 32ACP is discussed. The poster said that European 32ACP brass (factory loaded ammo) is thicker (S&B, Pvri Partizan, Fiocchi, and Geco), so European 32ACP bullets measure .309", while American brass...
    24 replies | 447 view(s)
  • Battis's Avatar
    04-03-2020, 08:26 PM
    Great info. There's a whole other world in the details that I never know about. I ordered a Lee 32ACP seater that should be here on 4/22.
    24 replies | 447 view(s)
  • Battis's Avatar
    04-03-2020, 07:34 PM
    If I didn't have OCD before, I have it now. I tested 7 of the 32 ACP rounds and 2 creeped inward too much. But, when I retested those two rounds, they didn't push in any further. So, basically, are the rounds that creep too much unsafe? What if...
    24 replies | 447 view(s)
  • Battis's Avatar
    04-03-2020, 06:48 PM
    Does the "push test" change with different calibers? Is the same amount of pressure used for, say, .45?
    24 replies | 447 view(s)
  • Battis's Avatar
    04-03-2020, 05:36 PM
    I think the 32 ACP cases are too short for the S&W Long dies, and I don't see a Lee 32 ACP crimp die available. I've been loading and shooting the rounds for a year or so with no problems, but, for some reason (too much time on my hands?) I started...
    24 replies | 447 view(s)
  • Battis's Avatar
    04-03-2020, 03:31 PM
    I use the 32 S&W long Lee dies to load 32 ACP but I can't get the die to crimp. I use a 32 WSL expander die, which works fine, but how do you crimp the 32 ACP? Is a crimp even needed?
    24 replies | 447 view(s)
  • Battis's Avatar
    04-01-2020, 12:41 PM
    I'm looking for info on disassembling (and later assembling) the bolt on a Spanish Destroyer. I have the bolt out of the rifle, I have the extractor off, but how do you remove the firing pin? On second thought... Realizing that I could most...
    0 replies | 106 view(s)
  • Battis's Avatar
    03-18-2020, 11:32 PM
    Battis replied to a thread Remington in Muzzleloading.
    Put a cap on a nipple (if it has to be pushed down, and doesn't fit all the way on, it's too small; if it is loose, pinch it on) and fire it off. Nothing wrong with a strong mainspring - a weak one can be a problem. If the nipple flash holes are...
    16 replies | 793 view(s)
  • Battis's Avatar
    03-16-2020, 09:14 AM
    I bought one recently. I fired it, using 1.1 grs Bullseye and .321 roundballs sized to .311 (flat on top and bottom). Fun gun. I bought the brass from Midway. https://www.midwayusa.com/product/1021324587?pid=785492
    20 replies | 792 view(s)
  • Battis's Avatar
    03-13-2020, 02:26 PM
    Triple 7 is 15% hotter than BP. I use the vegetable spray PAM (or a cheap substitute) for lube. But, and this is important, you must clean your gun very well after using PAM. I completely strip and clean my BP guns so it's not a problem. I found...
    19 replies | 861 view(s)
  • Battis's Avatar
    03-13-2020, 02:18 PM
    Battis replied to a thread GoodRX in Our Town
    One thing about GoodRX is that they will not tell you if you can get the drug cheaper somewhere else. I was all set to buy a drug through GoodRX that my insurance no longer covered, and for the heck of it I called my regular pharmacy and asked them...
    26 replies | 2195 view(s)
No More Results
About Battis

Basic Information

About Battis
Location:
Northeast

Statistics


Total Posts
Total Posts
1,645
Posts Per Day
0.64
General Information
Join Date
03-17-2013
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check