Titan ReloadingMidSouth Shooters SupplyStainLess Steel MediaRotoMetals2
WidenersRepackboxGraf & SonsLee Precision
Inline Fabrication
  • country gent's Avatar
    Yesterday, 09:29 PM
    My only 9mm is a Berretta 92, accuracy was always lackluster to say the least. jacketed and cast both. I tuned on the pistols fitting and trigger it got a little better but nothing near what my 1911s in 38 spl, 48 super,10mm and 45 were capable of....
    25 replies | 484 view(s)
  • country gent's Avatar
    Yesterday, 06:42 PM
    With the .452 sizer die that looks like a nose punch for one of the various 185 or 200 grain SWC nose punches.
    2 replies | 81 view(s)
  • country gent's Avatar
    Yesterday, 03:13 PM
    A couple 3 bags of ice in the body cavity is cheap insurance. While 60* isn't as big a problem a Sunny day with the carcass in the bed of a pick up may warm the carcass more than the air temp. A few bags of ice with the carcass wrapped in a sheet...
    16 replies | 349 view(s)
  • country gent's Avatar
    Yesterday, 03:02 PM
    I would also consider the old Bonanza Coax press. While still made it dates back many years and was considered one of the best or premier press for many many years. For pistol rounds one of the lyman truline jrs would be fun to use.
    7 replies | 135 view(s)
  • country gent's Avatar
    Yesterday, 01:36 PM
    I modified a rolling cutter cutting board for cutting patches. added a rail stop and made a plexiglass angle plate. I cut 5 sheets at a time. First cut the strips to width by running paper up to stop. I may cut a few groups of 5 sheets in one...
    7 replies | 165 view(s)
  • country gent's Avatar
    10-14-2018, 11:26 PM
    Its always interesting when working with a new person in any hobby or chore. Heres something to think about, even todays state of the art computer controlled machines still have tolerences on the parts they run. Even their parts arnt dead nuts on...
    13 replies | 319 view(s)
  • country gent's Avatar
    10-14-2018, 10:17 PM
    I have done them with a reamer when the right size is available better is a true boring head in the mill a sharp short bit and a few thou at a time makes a truly round base and very nice finish. If you have digital read out then indicate each cavity...
    16 replies | 434 view(s)
  • country gent's Avatar
    10-14-2018, 10:02 PM
    You could add career politicians to that list also.
    11 replies | 274 view(s)
  • country gent's Avatar
    10-14-2018, 10:00 PM
    I cut off my tank after it was well purged by several soap water flushings with a hand hacksaw working around it. I wouldn't recommend a torch or grinder, I didn't even like the idea of electric motor close while doing it. I started with a cast Iron...
    17 replies | 281 view(s)
  • country gent's Avatar
    10-14-2018, 05:02 PM
    I cut the ring and used a square and dividers to lay out the holes around the edge. I used the square set to 1/4" to give distance back from edge then a set of dividers to layout the 8 evenly spaced holes. I used a wrap of masking tape to lay out...
    19 replies | 373 view(s)
  • country gent's Avatar
    10-14-2018, 02:01 PM
    You would need to size the grease grooved bullet down a lot to paper patch it. Even to groove dia you looking at .008 addition with the paper. Bullet would need sized down to .450 or so to start with for a groove dia wrapped bullet. For a bore rider...
    8 replies | 222 view(s)
  • country gent's Avatar
    10-14-2018, 01:49 PM
    Any cast iron steel or stainless steel pot will work for this. If its a cook stove with covered heat areas a pot that fits in one will do good. If a wood tove for heating a small stand to hang the pot on in the stove will help a lot. A small stand...
    17 replies | 281 view(s)
  • country gent's Avatar
    10-14-2018, 01:40 PM
    While burn rates may be the same or very close that's only part of the equation here. Smokless powders are chemical in nature make up , coatings and retardants. How these different chemicals will interact with each other in the new blended powder...
    29 replies | 802 view(s)
  • country gent's Avatar
    10-13-2018, 09:35 PM
    On the helium tank if you wanted to Stiffen it up some bend a snug fitting ring of 1/8" X 1" and weld it in place around the cut edge. this will stiffen the top quite a bit and the sides some. Another thing is to cut a ring from the tank used and...
    19 replies | 373 view(s)
  • country gent's Avatar
    10-13-2018, 12:31 PM
    The q-tip will show rough surfaces and edges quickly. A good look at the edges under magnification at the edges and surfaces may reveal something also. Another quick check to do is set a dowel pin in 2 of the cavities and measure down to the face...
    9 replies | 274 view(s)
  • country gent's Avatar
    10-13-2018, 10:22 AM
    The harrels is very good I have 2 a shutzen and standard. Both are very accurate. The lymann 55 can be good, there used to be a conversion done to them called the culiver conversion that made them much easier and consistant to set. The Belding and...
    13 replies | 319 view(s)
  • Knarley's Avatar
    10-13-2018, 09:39 AM
    Mine is a 56-50 center fire. Use it for Cowboy action. Not a gun to be shooting for fast stage times, but it is a hoot to shoot and the style points are there. I'm not a real speed demon any way, so I TRY to at least look cool.
    23 replies | 710 view(s)
  • country gent's Avatar
    10-12-2018, 05:05 PM
    When I built my propane tank pot I made a second ring from the tank for a new full dia base. I cut 8 half holes on the top edge around it and welded it together. this allows the heat to flow up and around the pot better. my ring is down to the...
    3 replies | 151 view(s)
  • Knarley's Avatar
    10-12-2018, 04:44 PM
    I have a "Spencer" from Armi Sport. Fit and finish is excellent. Haven't shot it enough to have stuff falling off......yet. So far, really like the gun. Have a Pedersoli "Sharps". Have had it for years. Shoots well, have had no problems with it...
    23 replies | 710 view(s)
  • country gent's Avatar
    10-12-2018, 01:06 PM
    Henry claims that the brass they use is the same tensile strength as the steel is on their web site. I would think there is a coating on it to retard dulling and corrosion also but would be leary of BP loads in it do to the risk
    6 replies | 214 view(s)
  • country gent's Avatar
    10-12-2018, 12:21 PM
    country gent replied to a thread Help retreving iPad in Our Town
    I would be leary of the magnet since it may affect the screen and or drive adversely.
    41 replies | 1281 view(s)
  • Knarley's Avatar
    10-11-2018, 04:12 PM
    My guess would be that the original "45-70" was not a straight walled case. (Tapered) The chamber for the Winchester "45-70 Govt." would be.
    6 replies | 233 view(s)
  • country gent's Avatar
    10-11-2018, 04:03 PM
    I have done it and the way a lot do it is to mount barrel between centers and offset the tailstock for the taper then it can be turned in passes the full length. At one time factory contours were given in either taper per foot or taper per inch so...
    8 replies | 392 view(s)
  • country gent's Avatar
    10-11-2018, 03:55 PM
    country gent replied to a thread Sheep shears in Our Town
    That close fit between the top blade and bottom blade make the shearing action for the blades to cut cleanly. any clearance there and the wool binds them up and dosnt cut. The side spring maintains the zero clearance cutting. Run them a few days...
    9 replies | 310 view(s)
  • country gent's Avatar
    10-11-2018, 12:38 PM
    Something to consider with the Wilson style If your sizing smaller than standard the 45-70 std case holder may not hold the case from spinning when trimming. I have seen this with some straighter cases. If its only the neck your sizing down you may...
    13 replies | 359 view(s)
  • country gent's Avatar
    10-10-2018, 11:36 PM
    I believe so rfd, You may need to get a .457 pilot it comes with some a couple spacers and n extension to set up for shorter cases a set of primer pocket cleaners . I made an adapter to mount lyman vld chamfer and deburr in it so I could control...
    13 replies | 359 view(s)
  • country gent's Avatar
    10-10-2018, 10:41 PM
    I believe the first one to be an expanding mandrel for use I a lathe. It allows a part to be set up on the bore between centers. It is placed in the bore and tapped to expand tight into bore then the part is machined. To remove its tapped in the...
    10 replies | 673 view(s)
  • country gent's Avatar
    10-10-2018, 10:36 PM
    Chrome is hard on carbide also.
    4 replies | 218 view(s)
  • country gent's Avatar
    10-10-2018, 10:33 PM
    I used a version of the leather sling on my service rifle in NRA CMP matches it was thicker and didn't have the stretch other do. I did use the canvas sling occasionally in heavy rains to save the leather. I didn't care for the canvas since with the...
    13 replies | 354 view(s)
  • country gent's Avatar
    10-10-2018, 10:28 PM
    Maybe 32-40 or 38-55. depending on what you want to do with the rifle. 40-65 is also an option. I have heard the longer cartridges may require mods to the hammer spur to make loading easier
    19 replies | 554 view(s)
More Activity
About country gent

Basic Information

About country gent
Biography:
I was a NRA High Power rifle competitor for 20+ years with the service rifle also Long Range. I am widowed and Have Multiple Schlrocis. Im just getting into Black Powder Cartridges and cast rifle bullets now. Also have shot alot of handguns Ipsic and Bowling pins with cast bullets.
Location:
Northwest Ohio
Interests:
Dining shooting reading
Occupation:
Tool and die maker

Statistics


Total Posts
Total Posts
8,989
Posts Per Day
4.38
General Information
Last Activity
Yesterday 09:47 PM
Join Date
03-03-2013
Referrals
0

4 Friends

  1. Kenny Wasserburger Kenny Wasserburger is offline

    Boolit Buddy

    Kenny Wasserburger
  2. Knarley Knarley is offline

    Boolit Buddy

    Knarley
  3. ktapply ktapply is offline

    Boolit Mold

    ktapply
  4. TXGunNut TXGunNut is offline

    Boolit Master

    TXGunNut
Showing Friends 1 to 4 of 4
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check