Graf & SonsRotoMetals2WidenersStainLess Steel Media
Lee PrecisionInline FabricationRepackboxMidSouth Shooters Supply
Titan Reloading
  • country gent's Avatar
    Today, 11:24 AM
    Have you tried reseating resetting the pins in the block. If you have .157 pins the holes for them are probably .1565 for the correct press fit. .150 pins will be loose in them. The ends of the existing pins should be a full radius and resetting...
    4 replies | 69 view(s)
  • country gent's Avatar
    Yesterday, 11:44 PM
    country gent replied to a thread Finally happenned in Our Town
    This time of year deer collisions go way up here. Farmers are running crops off and that keeps them moving and stirred up a lot more.
    20 replies | 363 view(s)
  • country gent's Avatar
    Yesterday, 06:46 PM
    A rifle with a tight necked chamber and necks turned to fit can be very accurate. This is a bench rest technique that leaves .001 or less neck chamber clearance. It alighns the cartridge very accurately and can result in very concentric ammo. This...
    17 replies | 353 view(s)
  • country gent's Avatar
    Yesterday, 10:53 AM
    1, 1 1/2, and 2f are different screen sizes to grade. A mixture is just that and may create other problems, the heavier 1 f kernals will flow different from the 2f kernals separating in the measure. I believe buffalo arms has a chart giving kernel...
    11 replies | 270 view(s)
  • country gent's Avatar
    10-21-2018, 05:17 PM
    Sinclairs or K&M work good. Simply neck turning for a factory chamber may not give a big improvement over standard necks selected for consentric neck wall thickness as it adds to the clearance between case and chamber. Better is to form brass from a...
    17 replies | 353 view(s)
  • country gent's Avatar
    10-21-2018, 01:17 PM
    I use the paper cutter for it all. no templates per say. I have a rolling cutter board. I added a rail stop and flat surface out side of the cutter. Like is on a sheet metal shear this allows me to cut sheets from the roll of Seth Cole paper. these...
    4 replies | 187 view(s)
  • country gent's Avatar
    10-21-2018, 10:11 AM
    country gent replied to a thread Chrono-madness! in Cast Boolits
    Weall it only takes a few minutes to fire the test rounds, and when done you know the set up is good and the chrono is reading correctly, with the test 22 or pellets. Just a way to save test rounds to know all is well before shooting them
    30 replies | 689 view(s)
  • country gent's Avatar
    10-20-2018, 11:09 PM
    country gent replied to a thread Chrono-madness! in Cast Boolits
    Another thing to consider is to use a .22 rimfire with a good ammo or a spring piston air rifle and the same pellets to confirm set up and accuracy each use. Either will give consistant results over time. A tin of pellets or brick of 22s set aside...
    30 replies | 689 view(s)
  • country gent's Avatar
    10-20-2018, 10:59 PM
    A lot no longer wrap with the tail wound under the bullet. leave 3/16" over hang on base and wrap bullet then fold base under it should leave a small bit of the bullets base showing in the center and a much flatter base to work with. I get better...
    10 replies | 297 view(s)
  • country gent's Avatar
    10-20-2018, 07:43 PM
    The turned stock is for your bullet to be formed from. You form the bullets ogive on it and then cut to needed length. The shim is like the shim in 38spl 357 dies sets all it does is raise the die setting by its thickness to not crimp with out...
    5 replies | 173 view(s)
  • country gent's Avatar
    10-20-2018, 07:33 PM
    The correct fit and correct stakeing would be acceptable also. the Stake should have been a complete ring around not the dimples and nowhere as deep as those were, we did cut a small bevel for the stake to overlay the part when done but wen don it...
    40 replies | 1715 view(s)
  • country gent's Avatar
    10-20-2018, 07:20 PM
    I shoot PP with grease cookies in 45-70 45-90 and 40-65. Depending on powder, powder charge and barrel length, which all factor in to How thick a cookie you need. I use a heavy wad .060 rubber fiber over powder the grease cookie then a playing card...
    12 replies | 231 view(s)
  • country gent's Avatar
    10-19-2018, 09:06 PM
    I have them from BACO and have made my own. I usually make one modified for use in the seater die. Make a square ended p lug to fit the threads in your die of the appropriate length will work. Another way is to make a dummy...
    5 replies | 173 view(s)
  • country gent's Avatar
    10-19-2018, 05:21 PM
    A small die set could be made for this and used in a vise or small ahrbor press.a reloading press could be done also. Materials would be : 6" 3/4 X1 flat stock 6" of round stock close to desired caliber ( bigger not...
    18 replies | 706 view(s)
  • country gent's Avatar
    10-19-2018, 04:45 PM
    country gent replied to a thread Bullets in a fire in Our Town
    Had a pick up truck catch fire years ago behind the seat were 2 boxes of 12 ga bird shot shells. some the crimp unfolded others the sides split, these were the plastic shells not the older waxed paper hulls.
    31 replies | 878 view(s)
  • country gent's Avatar
    10-19-2018, 01:26 PM
    A press fit is a simple thing to do and only requires you have the stock to make it on the new part. The hard part is measuring to know you have the true .001-.002 interference needed. On replacement parts this may be a problem as they are made for...
    40 replies | 1715 view(s)
  • country gent's Avatar
    10-19-2018, 12:15 PM
    Wilton is a major name in vises and very good. The assortment of soft jaws is also good advice. To save marring and gouging a vise produces a lot of force. Another is a supply of hard maple 1"X2"x the length of the jaws for making jaws. Clamping a...
    33 replies | 921 view(s)
  • country gent's Avatar
    10-19-2018, 12:02 PM
    I have a Meacham bushing die with out the decap head. It allows for the neck only to be sized and to adjust the neck tension with different bushings. I use it for 45-70,45-90 and 40-65 by changing bushings as needed. I also have bushings for both...
    8 replies | 328 view(s)
  • country gent's Avatar
    10-18-2018, 07:37 PM
    The worse part of this is there is no "coming back" from this fix. Those stakes are always going to be there.
    40 replies | 1715 view(s)
  • country gent's Avatar
    10-18-2018, 03:56 PM
    The 44 can be loaded down to comfortable levels or even 44 spl loads used. Another recoil reducing technique is to go to a lighter bullet instead of the240-270 grn most favor work up a light load using 180-200 grn bullets that fill a lot of the...
    36 replies | 974 view(s)
  • country gent's Avatar
    10-18-2018, 03:44 PM
    Also now several others are producing them Savage comes to mind. The Savage is getting some great reviews and it has the easy barrel swap Savage is known for. Have a friend that just had a kelby action built up into a pistol. There is still a...
    16 replies | 508 view(s)
  • country gent's Avatar
    10-18-2018, 11:11 AM
    One way to look at this is How many parts are there in a given firearm? Every part has a tolerance on size hardness material composition of its own. every part is fitted into this machine to work with the other parts. While the same maunfaturer...
    18 replies | 613 view(s)
  • country gent's Avatar
    10-18-2018, 10:55 AM
    In my big ladle pot ( 100lbs+) I use a mixture of wood and paraffin to flux. I did try the flux in a tin for soldering pipe joints and such, worked but not any better or wrse than the wood paraffin mix. I add the wood and a small ball of paraffin...
    10 replies | 346 view(s)
  • country gent's Avatar
    10-17-2018, 11:11 PM
    As a side note a lot of AR barrels had the twist stamped on them somewhere usually ahead of the extension or at the muzzle end
    9 replies | 342 view(s)
  • country gent's Avatar
    10-17-2018, 11:10 PM
    I do it similar to above. I use a brush with patch cut to make a tight fit. insert rod thru muzzle and screw it on. Pull into rifling. put a masking tape tail pointing up right against the muzzle and pull out for 1 revolution. measure between...
    9 replies | 342 view(s)
  • country gent's Avatar
    10-17-2018, 08:37 PM
    Normally sizing is recommended for up to around .002-.003 reductions. Your wanting .008-.009. This could possibly be done in push thru sizing dies in 2 passes. This much in one pass may not size down but shave down removing metals. I would recommend...
    20 replies | 515 view(s)
  • country gent's Avatar
    10-17-2018, 07:49 PM
    Starting with the cold pot is good advice. Another trick is a steel pan big enough to sit on top of your pot to use to pre heat the bullets. Preheating the bullets to 250-300* in a separate container for 20 mins or so will also take care of any...
    12 replies | 368 view(s)
  • country gent's Avatar
    10-17-2018, 07:34 PM
    For just the bezel repair you might check with a local jeweler. He might handle it quickly and reasonably. In reality accuracy is much more today than it was years ago. For years a caliper or mike that measured to the...
    28 replies | 1259 view(s)
  • country gent's Avatar
    10-17-2018, 04:31 PM
    Nun2kute Making your own is fun, satisfying and saves some money ( sort of like reloading goes LOL). When I did mine in the 80s parts were nearly as available, or as many selections. Most for a flat top match rifle just cut the top off a AR service...
    10 replies | 323 view(s)
  • country gent's Avatar
    10-17-2018, 12:03 PM
    Profile of the firing pin ( a small ring or rough surface), size smaller pins create a smaller tighter indent that is more apt to pierce, to long may literally push thru the cup, a oversized hole around the firing pin allows for cratering and or the...
    17 replies | 484 view(s)
More Activity
About country gent

Basic Information

About country gent
Biography:
I was a NRA High Power rifle competitor for 20+ years with the service rifle also Long Range. I am widowed and Have Multiple Schlrocis. Im just getting into Black Powder Cartridges and cast rifle bullets now. Also have shot alot of handguns Ipsic and Bowling pins with cast bullets.
Location:
Northwest Ohio
Interests:
Dining shooting reading
Occupation:
Tool and die maker

Statistics


Total Posts
Total Posts
9,022
Posts Per Day
4.38
General Information
Last Activity
Today 04:30 PM
Join Date
03-03-2013
Referrals
0

4 Friends

  1. Kenny Wasserburger Kenny Wasserburger is offline

    Boolit Buddy

    Kenny Wasserburger
  2. Knarley Knarley is offline

    Boolit Buddy

    Knarley
  3. ktapply ktapply is offline

    Boolit Mold

    ktapply
  4. TXGunNut TXGunNut is offline

    Boolit Master

    TXGunNut
Showing Friends 1 to 4 of 4
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check