Inline FabricationGraf & SonsTitan ReloadingLee Precision
RotoMetals2RepackboxWidenersMidSouth Shooters Supply

  • country gent's Avatar
    Today, 05:45 PM
    We had one at work for some specialty jobs. I suspect the ones used for making moulds were more than likely made in house by the companies for a couple reasons. One when used as they did the play in the jaws and threads would be a critical issue....
    9 replies | 219 view(s)
  • country gent's Avatar
    Today, 05:29 PM
    country gent replied to a thread What are they in Our Town
    I'm not sure on the rubber pieces being vise jaws since the bolt heads would still mar. I'm thinking a machine wiper or mount feet of some sort. On the levers I'm guessing window or sliding door latches
    21 replies | 539 view(s)
  • country gent's Avatar
    Today, 01:05 PM
    The case walls thickness is tapered and gets thicker as it moves towards the head. Shoulders and necks + a little past the shoulder are annealed when the case are made to soften this area of the brass, it takes the most forming and work hardens ...
    6 replies | 557 view(s)
  • country gent's Avatar
    Yesterday, 11:01 PM
    Lighter bullets will reduce recoil ( also range at times). Velocity lowered also reduces felt recoil. Rifle weight makes a big difference in felt recoil, a 7 LB rifle recoils more than a 9lb rifle and a 9lb rifle is more than the 12 lb rifles....
    8 replies | 195 view(s)
  • country gent's Avatar
    Yesterday, 10:51 PM
    I load 45-70 and 45-90 with 1F Olde Ensforfe the coarser granulation fills the case faster and then can be adjusted to velocity with compression and added charge. My load with 1F and a 550 grn bullet is giving 1190 fps and 12 fps extreme Spread over...
    8 replies | 195 view(s)
  • country gent's Avatar
    Yesterday, 10:41 PM
    A brief description of the new cutter pilots geometry. they are the .186 stem for the Redding trimmer 3/8" long with a small flat for orientation. The body is turned to cases inside neck dia. the outside end away from stem is chamfered at 8* and...
    1 replies | 178 view(s)
  • country gent's Avatar
    Yesterday, 09:12 PM
    country gent replied to a thread 38-55 bullet sizing in Leverguns
    .381 - .379 is doable (.002) but if these are commercial hard cast they may take some force to size. A push thru die used in a reloading press would be best for this, more leverage, pushes on bottom of bullet instead of nose. And allows bullet to...
    6 replies | 134 view(s)
  • country gent's Avatar
    Yesterday, 08:59 PM
    I use Molebnium Disulfide for powder measures. If the cast iron body looks "coarse" or grainy then I give it a coat of wax with moly mixed in it to help fill the voids or grains. Any dry lube will work. Moly, Gtaphite, silicone, micas and wax have...
    11 replies | 221 view(s)
  • country gent's Avatar
    Yesterday, 01:34 AM
    I turn up a wood dowel to match the sprues angle then use lapping compound to polish it up. It works great for me. I've bought several lyman moulds and gotten good ones. I have had to lapp some moulds for size with older rifles and bores that were...
    40 replies | 1050 view(s)
  • country gent's Avatar
    Yesterday, 01:26 AM
    I shot NRA High power rifle ( both service rifle and match rifle) Long Range and 3 position small bore. In High power it was a M1a or garand with rear aperture and blade front, Match rifle was set up with warner rear gehmen aperture and globe...
    47 replies | 939 view(s)
  • country gent's Avatar
    Yesterday, 12:59 AM
    The army finished some M14 national match stocks with an epoxy. It was a very involved process designed to push as much epoxy as far as possible into the wood stock. It involved a "soak time" in a vacuum pot at elevated temps of 180* or so. This...
    16 replies | 285 view(s)
  • country gent's Avatar
    02-17-2019, 07:50 PM
    I normally use Bisonite steel bed for rifles. its fairly thick and easy to work with. Mixing is different as its 10-1 ratio. There is a thickening powder for it if desired. Champions Choice in Laverge Tennessee sold it when I bought my last tub....
    16 replies | 285 view(s)
  • country gent's Avatar
    02-17-2019, 07:23 PM
    There was a set up to use a torque wrench on place of the press handle to crimp to a set ft lbs or inch lbs instead of the cam over or stop.
    29 replies | 432 view(s)
  • country gent's Avatar
    02-17-2019, 03:09 PM
    I would find a piece of cold roll steel flat stock. Glue the old one back together and scribe around it. drill the hole and cut out the shape drilling and tapping the needed holes cut proud and then file or grind with a Dremel tool to size and...
    6 replies | 185 view(s)
  • country gent's Avatar
    02-17-2019, 02:49 PM
    Heres a example of shooters and their good nature and honesty. Just before the Nationals one year I left my shooting mat at a range in mich after a match. Bought a new one when I got to Perry on commercial row. The first day of the cmp/dcm matches...
    16 replies | 612 view(s)
  • country gent's Avatar
    02-17-2019, 12:12 PM
    If you maintain the same loaded overall length then short brass really isn't an issue except for crimp if you apply one. Maintaining the same overall length on the loaded rounds puts the bullets base in the same place in the case whether brass is to...
    29 replies | 432 view(s)
  • country gent's Avatar
    02-17-2019, 12:49 AM
    In my 45-90 I shoot several grease groove bullets. My rifle is a C Sharps Hepburn green mountain 1-18 twist 34" barrel. The 3 bullets I shoot are 1) the lyman 457125 510 grn govt round nose ...
    8 replies | 275 view(s)
  • country gent's Avatar
    02-16-2019, 03:35 PM
    The piece for the lyman trimmer isn't going to be to hard to do. The .300" dia and .250 recess isn't going to have mush thickness to the rim though .300-.250 / 2 = .025 lip but should be okay with a solid fill of jb weld to support it. Im assuming...
    4 replies | 187 view(s)
  • country gent's Avatar
    02-16-2019, 01:08 AM
    The Lymann 55 was the measure used to convert to one of the most accurate repeatable measures made. The culiver conversion measure. Bench and accuracy specialists swear by this measure. I believe the Harrels is a modern copy of the Culiver also. ...
    20 replies | 358 view(s)
  • country gent's Avatar
    02-16-2019, 12:56 AM
    This weeks projects were 4 flash hole deburring tools and a few need case trimmer pilots I modified a little' The flash hole deburring tools will do 20 cal up to 45 cal ( maybe 50 cal) and a case...
    1 replies | 178 view(s)
  • country gent's Avatar
    02-16-2019, 12:18 AM
    I make baffles from old plastic pop bottles or aluminum flashing. Its not hard to do and requires few tools. a vee type is simple to make. Cut a pop bottles center section out square and clamp between 2 pieces of flat wood...
    20 replies | 358 view(s)
  • country gent's Avatar
    02-15-2019, 03:59 PM
    There are brazes for diecast metals the problem is the chrome plating on this part will keep it from getting a good bond. The other is aluminum and these metals are hard to braze weld since thes no real color change, Steels turn red when ready to...
    24 replies | 704 view(s)
  • country gent's Avatar
    02-15-2019, 03:54 PM
    Put an add in Swapping and selling for some test bullets to try and see what the rifle likes and shoots best. 20 bullets can give a very good idea. This will give you test data to choose by and when thru you have the lube and mould number maker to...
    30 replies | 651 view(s)
  • country gent's Avatar
    02-15-2019, 03:37 PM
    Do you want to use iron sights or a scope? A C Sharps Low wall or high wall on 32-40 or 38-55 should be useable
    19 replies | 815 view(s)
  • country gent's Avatar
    02-15-2019, 03:23 PM
    I use the Harrels also for smokeless powders, I have the standard size measure and the smaller Schutzan sized measure, they are very good and accurate the click adjustments make them very repeatable as to setting also. I also use the RCBS little...
    20 replies | 358 view(s)
  • country gent's Avatar
    02-15-2019, 01:36 AM
    The chamber brush on Gi tools did and excellent job pulling separated cases from m 1as and garands. I have used bore brushes in the past to pull them also. Another way s to wrap a patch around the brush and push thru from muzzle the brush patch...
    3 replies | 193 view(s)
  • country gent's Avatar
    02-15-2019, 01:25 AM
    Glue it together and carefully drill a pin hole in the boss and epoxy a pin in. on the out side face cut a piece of brass steel or aluminum sheet metal .080-.095 thick to match outside dimensions. With a coarse file rough up handle and one side of...
    24 replies | 704 view(s)
  • country gent's Avatar
    02-14-2019, 03:53 PM
    It was and is common practice to ID cavities of multi cavity moulds for several reasons. Mostly its done with rifle bullets. I used a O on the nose of one cavity and the other bare. But a dimple, X, 8, Z or other mark ( I preferred marks that were...
    19 replies | 691 view(s)
  • country gent's Avatar
    02-14-2019, 03:35 PM
    We had several 1X2 with a slot milled in it and a cover . I believe it held 10 or 15 of the neco wafers in it the bottom wafer was visible. When you broke it the next dropped down into view. Worked good and saved trips down range. Aspirins we set in...
    9 replies | 271 view(s)
  • country gent's Avatar
    02-14-2019, 03:23 PM
    A lot of times when the head comes off the actual thread is loose and can be walked out with a pick and small hammer. I was spoiled at work getting stuck screws and bolts out. I ran the edm sinker. a allen wrench socket just under screw size and...
    11 replies | 192 view(s)
More Activity
About country gent

Basic Information

About country gent
Biography:
I was a NRA High Power rifle competitor for 20+ years with the service rifle also Long Range. I am widowed and Have Multiple Schlrocis. Im just getting into Black Powder Cartridges and cast rifle bullets now. Also have shot alot of handguns Ipsic and Bowling pins with cast bullets.
Location:
Northwest Ohio
Interests:
Dining shooting reading
Occupation:
Tool and die maker

Statistics


Total Posts
Total Posts
9,641
Posts Per Day
4.42
General Information
Last Activity
Today 08:51 PM
Join Date
03-03-2013
Referrals
0

4 Friends

  1. Kenny Wasserburger Kenny Wasserburger is offline

    Boolit Master

    Kenny Wasserburger
  2. Knarley Knarley is offline

    Boolit Buddy

    Knarley
  3. ktapply ktapply is offline

    Boolit Mold

    ktapply
  4. TXGunNut TXGunNut is offline

    Boolit Grand Master

    TXGunNut
Showing Friends 1 to 4 of 4
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check