Titan ReloadingRotoMetals2WidenersRepackbox
Lee PrecisionInline FabricationADvertise here

  • country gent's Avatar
    Yesterday, 07:12 PM
    You need some taper to ease extraction a truly straight walled case will drag the full length. On an action that "pops" the case out it may only kick it out a little bit meaning it will need to be pulled out by had and on most single shots this is a...
    30 replies | 1359 view(s)
  • country gent's Avatar
    Yesterday, 03:38 PM
    I loaded 222 rem for several years with a lee standard mallet tool. This was for a savage 110 varmint model. used the basic tool and a old bottle caper instead of the mallet. Rifle would do 3/4" at 100 yds with this ammo and the loads it liked. I...
    25 replies | 569 view(s)
  • country gent's Avatar
    02-18-2020, 10:33 PM
    I would strip off what you can then , sand as needed with blocked sand paper. I dont care for steel wool it rounds corners and makes details fuzzy looking. Tru oi makes a nice easily repairable finish. I thin it 50/50 put on a light coat then wet...
    13 replies | 206 view(s)
  • country gent's Avatar
    02-18-2020, 10:11 PM
    I think its fine. Appears a spin off of the 700 action so we will have a pistol numbered action for long range pistol projects saving a lot of fiddling round. Betting it wont take treebone, boyds or others to have a wood wood laminate stock for it...
    32 replies | 878 view(s)
  • country gent's Avatar
    02-18-2020, 01:08 PM
    A straight edge or flat bar to set the moulds on when closig will help to pre align them when closing. I use a piece of angle iron set on the bench wide side down point up.
    6 replies | 134 view(s)
  • country gent's Avatar
    02-17-2020, 03:07 PM
    I like pulling bullets in the press a piece of pvc pipe that fits over the ram shell holder just longer than and a pair of side cuts. this pulls bullets very quickly. Saves a lot of stroke. As to the primers the sizing die or one the case will...
    22 replies | 458 view(s)
  • country gent's Avatar
    02-17-2020, 02:52 PM
    I use windex with vinegar as a range cleaning solvent for BP. Ballistol should be very good for wiping and cleaning at your ratio. The Napa water pump oil or cutting and grinding oils ill lubricate but may not clean as well. I have read where some...
    7 replies | 275 view(s)
  • country gent's Avatar
    02-17-2020, 12:35 PM
    Now is the hard part the "wait" for the rifle. Its the 2 months before Christmas again.
    62 replies | 8788 view(s)
  • country gent's Avatar
    02-17-2020, 12:08 PM
    country gent replied to a thread Scope over hang ? in Our Town
    You should be fine with t like that. Get the best spacing you can. Lock rings on base/rail. Then lap to true alignment and mount scope. Lapping the rings will help ncrease the holding power allowing the full surface to work not just the high points....
    7 replies | 261 view(s)
  • country gent's Avatar
    02-17-2020, 11:52 AM
    The solder wont take to the corroded metal sight or barrel, even the old solder may give a problem. Clean both parts to good metal. Lightly flux For this type gob I like the flat silver solder sheet about .005 thick, Cut a piece of this to match...
    11 replies | 364 view(s)
  • country gent's Avatar
    02-17-2020, 11:40 AM
    I would try a simple cleaning with dish soap and water really work up a lather as this floats the crud out, do both the male and female threads several times. Rinse and dry well. If you dont clean both threads one will contaminate the other quickly....
    19 replies | 328 view(s)
  • country gent's Avatar
    02-16-2020, 09:36 PM
    If your handles use a shoulder bolt at the hinge join it may not be the thread but wear between head and the 2 handles combined. Here a new shoulder bolt may do the trick or just a small amount at a time removed from where the nut bottoms on it....
    6 replies | 134 view(s)
  • country gent's Avatar
    02-16-2020, 09:23 PM
    The biggest thing is stop thinking about it, Dont dwell on it. You will subconsciously talk yourself into shooting the wide shot every time. Dont dwell on the bad shots but on the good shots. The mind is a powerful tool
    11 replies | 343 view(s)
  • country gent's Avatar
    02-16-2020, 02:28 PM
    Something to keep in mind unless the screw really needs to be hardened soft is better, This way the screw wears and not the holes female threads. Its easier on tooling also. A soft screw is easier to remove it breaks. ...
    6 replies | 197 view(s)
  • country gent's Avatar
    02-16-2020, 02:15 PM
    Im thinking the grooves wet wrap and bac smear and heavier paper may be hindering the paper release from the bullet. I shoot paper patched BP rounds and I use Seth Cole 55W (a shade under .002 thick) dry wrapped tight. The bullets are smooth sided ...
    10 replies | 309 view(s)
  • country gent's Avatar
    02-16-2020, 02:06 PM
    The biggest thing is to keep a good "book" so patterns and results are shown over several days. The longer these are kept the better the data becomes. For long range knowing the zeros for a given range, at long range a small miscalculation in...
    11 replies | 280 view(s)
  • country gent's Avatar
    02-16-2020, 01:44 PM
    I have one of the early rcbs units with the charger separate from the scales, an IR connection reads the scales. It is slow tricking the charge for a 308 up from zero ( around 41 grns) but was accurate. What worked much better was to drop a charge...
    17 replies | 2378 view(s)
  • country gent's Avatar
    02-16-2020, 01:13 PM
    I have the gem pro 250 and its been a great scales. Its got .02 grn resolution. I bought mine when they were $125.00. My only issue is trickling up as it takes a little to fet it started again once it settles
    17 replies | 2378 view(s)
  • country gent's Avatar
    02-16-2020, 01:04 PM
    country gent replied to a thread Ruger mki target in Rimfire Area
    Other than the assembly disassembly to test check the trigger as you go, job isnt hard to do and a few fine stones and light oil will do a fine job. I did my 8" mark 2 worked down with stones close setting length of pull / break and weight. The a...
    9 replies | 358 view(s)
  • country gent's Avatar
    02-16-2020, 12:53 PM
    Some of the bigger vendors here have a cable set up they run thru the trigger guards and only remove to allow handing. it has a joint every 18" or so. Keeps things secured but again every showing requires removal. Most shows have guards at the doors...
    23 replies | 1436 view(s)
  • country gent's Avatar
    02-16-2020, 12:14 PM
    Notice now how the side of the nipple base is parallel to the cut out on the stock, a much more professional look than before. Plus it looks like the cap will get a much more direct flatter hit from hammer. Better ignition and the solid even hit...
    24 replies | 670 view(s)
  • country gent's Avatar
    02-15-2020, 11:44 PM
    If you go the lathe bored route use a solid carbide boring bar. They are much stiffer this cuts down a lot on tool flex and chatter. Boring a cavity requires a small bar and the shortest stiffest is best. For cutting nose...
    44 replies | 2805 view(s)
  • country gent's Avatar
    02-15-2020, 10:06 PM
    Larry not to hi jack the thread but for awhile in my long range / coarse rifle at 600 yds I shot a Starke 6 mm vld flat based 105 grn ( while it was available wish Id stocked a bigger supply). At 600 it gave better scores and wind bucking than the...
    11 replies | 280 view(s)
  • country gent's Avatar
    02-15-2020, 04:57 PM
    country gent replied to a thread rifle barrels in Our Town
    Ive burnt up a few krieger barrels shooting NRA high power. My M1As wore them. M ARs have kiegers, and a lilja on them my match rife wore a hart otc contour. This rifle did double duty Across the course and long range. Other rifles have shilen ( a...
    16 replies | 579 view(s)
  • country gent's Avatar
    02-15-2020, 04:42 PM
    It isnt the subsonic or the supersonic velocities that are a problem its the transition in flight between the 2 that is. Your 45-70 isnt showing it because its staring out sub sonic and staying there all the way to the target. When a bullet foes...
    11 replies | 280 view(s)
  • country gent's Avatar
    02-14-2020, 08:08 PM
    Not familiar with those 2 measures, Some use a shelf edge for off press mounting, a small c clamp on the back some use 2 screws to hold it tight to the shelf. Here would be the lymann 55, Belding and mulls, Harrels and some Redding measures that...
    25 replies | 644 view(s)
  • country gent's Avatar
    02-14-2020, 07:50 PM
    One crude test is to spread a bed sheet under and in front of the rifle and shoot a few rounds look for unburnt powder laying there on it. With the moderate charge of powder and bullet weight of...
    8 replies | 236 view(s)
  • country gent's Avatar
    02-14-2020, 08:33 AM
    Before lapping or fire lapping I would recommend slugging it as best you can to see what you are working with. If its a tight bore good if its large already you van only Lapp it bigger not smaller.
    10 replies | 435 view(s)
  • country gent's Avatar
    02-14-2020, 07:34 AM
    In a single shot action where camming and extraction can be weaker"that taper is a plus.
    30 replies | 1359 view(s)
More Activity
About country gent

Basic Information

About country gent
Biography:
I was a NRA High Power rifle competitor for 20+ years with the service rifle also Long Range. I am widowed and Have Multiple Schlrocis. Im just getting into Black Powder Cartridges and cast rifle bullets now. Also have shot alot of handguns Ipsic and Bowling pins with cast bullets.
Location:
Northwest Ohio
Interests:
Dining shooting reading
Occupation:
Tool and die maker

Statistics


Total Posts
Total Posts
11,245
Posts Per Day
4.42
General Information
Last Activity
Yesterday 10:41 PM
Join Date
03-03-2013
Referrals
0

4 Friends

  1. Kenny Wasserburger Kenny Wasserburger is offline

    Boolit Master

    Kenny Wasserburger
  2. Knarley Knarley is offline

    Boolit Buddy

    Knarley
  3. ktapply ktapply is offline

    Boolit Mold

    ktapply
  4. TXGunNut TXGunNut is offline

    Boolit Grand Master

    TXGunNut
Showing Friends 1 to 4 of 4
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check