MidSouth Shooters SupplyRepackboxInline FabricationADvertise here
Lee PrecisionWidenersRotoMetals2Titan Reloading

Tab Content
  • rfd's Avatar
    06-04-2020, 08:44 AM
    what joe just typed, get the L&R rpL05 lock. it will not be a perfect drop-in fit, but darned close to it. i've done that to at least 2 or 3 investarms flinters (rebranded as lyman, cabelas, DGW, etc). ...
    12 replies | 254 view(s)
  • rfd's Avatar
    06-01-2020, 08:22 AM
    there's a valid reason for using a muzzle protector. evolving military weapon requirements are just that - military needs of the business, a broken rod means out-of-business - and that came to dictate a rod that can take more than a beating, thus...
    8 replies | 280 view(s)
  • rfd's Avatar
    05-29-2020, 08:27 PM
    correct with one exception - if the measuring is done in a controlled manner it becomes an "experiment of one" that will only matter to the experimenter. been there, done that for over 65 years of muzzleloading.
    17 replies | 290 view(s)
  • rfd's Avatar
    05-29-2020, 08:17 PM
    i'll stand by my experience and that of the target folks - tight patched loads that require a stout short starter and a brass rod win the vast majority of matches. period. HOWEVER, tight loads are simply not my style with a flintlock long gun. ...
    17 replies | 290 view(s)
  • rfd's Avatar
    05-29-2020, 07:09 PM
    what ed and bent said - tight mic the cloth and use that as a *guideline* because all cloth is different, sometimes even within the same lot. when you find a cloth that works well for ya, buy up as much as you can and yer set for that gun and that...
    17 replies | 290 view(s)
  • rfd's Avatar
    05-23-2020, 09:05 AM
    rfd replied to a thread .45 cal. Patch Size? in Muzzleloading.
    i prefer either prelubed patch strips or ball boards - makes for perfect loads every load, and no specific patch diameter needed (but yes - patch thickness absolutely needs to be predetermined and well tested).
    16 replies | 939 view(s)
  • rfd's Avatar
    05-23-2020, 08:32 AM
    rfd replied to a thread .45 cal. Patch Size? in Muzzleloading.
    what ed said. what kinda load does yer shooting needs require? the matter of the load itself, in terms of loose or tight, is solely dependent on cast ball diameter and patch thickness. a .445 ball will work just fine, it's up to you to get...
    16 replies | 939 view(s)
  • rfd's Avatar
    05-17-2020, 06:35 AM
    great article, wayne. plenty of good scoop for all tumbler fans. lee's SSE magazine is one of the best, if not the best out there for all things BPCR. highly recommended to all, go get yerself on the SSE mailing list! i finally chose to go a...
    25 replies | 1426 view(s)
  • rfd's Avatar
    05-15-2020, 08:07 PM
    going afield, i like the ubiquitous .38spl centerfire round. that's why months ago i bought a model 67 as the big brutha to my model 642. yes, it's got a fat bbl with a few more added ounces to heft around, but that's ok by me. having vision...
    127 replies | 9965 view(s)
  • rfd's Avatar
    05-15-2020, 07:31 AM
    rfd replied to a thread Opinions on Rem 783. in Factory Rifles
    to add to my first post in this thread .... i wanted a 6.5 creedmoor bolt gun where the action and perhaps bbl might become become the basis of a ELR rifle (700yds and much Much further out there). brand and plastic stock didn't much matter. i...
    36 replies | 5702 view(s)
  • rfd's Avatar
    05-14-2020, 12:10 PM
    rfd replied to a thread Opinions on Rem 783. in Factory Rifles
    for the very most part, all major brand bottom feeder bolt offerings will be a gamble of sorts and your requirements and expectations are all part of that equation.
    36 replies | 5702 view(s)
  • rfd's Avatar
    05-09-2020, 03:02 PM
    depends on what "short" is. easier to it it with a hammer, i'd think. but i'd rather get it right from the get-go rather than to fudge it later.
    41 replies | 4165 view(s)
  • rfd's Avatar
    05-09-2020, 01:47 PM
    i find it best to cut the paper template to the exact size, then file the brass template in stages of sorts, to produce proper patches. if the brass template is a little too short, time to start all over.
    41 replies | 4165 view(s)
  • rfd's Avatar
    05-07-2020, 07:00 PM
    ruger american compact 9mm w/vortex venom red dot, in a clinger kydex, AIWB. S&W 642c .38spl in a pocket holster.
    72 replies | 4419 view(s)
More Activity
About rfd

Basic Information

Age
74
About rfd
Location:
NJ via TX

Signature


"Owning a handgun doesn't make you armed any more than owning a guitar makes you a musician." - Jeff Cooper

Statistics


Total Posts
Total Posts
3,551
Posts Per Day
1.33
General Information
Last Activity
Yesterday 08:37 AM
Join Date
02-07-2013
Referrals
0
Home Page
http://www.buffalorifles.org

5 Friends

  1. Captain*Kirk Captain*Kirk is offline

    Boolit Buddy

    Captain*Kirk
  2. dromia dromia is offline

    Moderator Emeritus

    • Send a message via Yahoo to dromia
    dromia
  3. Flintlock1812 Flintlock1812 is offline

    Boolit Bub

    Flintlock1812
  4. ktapply ktapply is offline

    Boolit Mold

    ktapply
  5. vikingson57 vikingson57 is offline

    Boolit Bub

    vikingson57
Showing Friends 1 to 5 of 5
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check