RepackboxLee PrecisionRotoMetals2MidSouth Shooters Supply
Inline FabricationTitan ReloadingADvertise hereReloading UK

Tab Content
  • Guardian's Avatar
    Yesterday, 08:11 PM
    If you are willing to drive a bit, try Metal Supermarkets 2000 Pewaukee Road Suite M, Waukesha, WI, 53188. They should be able to get it if they don’t have the size you want. Tractor Supply usually has some small pieces in the welding aisle, if...
    17 replies | 410 view(s)
  • Guardian's Avatar
    01-23-2021, 12:25 AM
    Muffle furnace First time I used it I had a block of brass afterward. I put a PID on it after that.
    17 replies | 410 view(s)
  • Guardian's Avatar
    01-21-2021, 07:52 PM
    I haven’t pinned my LEE handles, but I do have tap them back on occasionally. I have to do the same with a set of H&G handles. I’ve got several sets of MP handles. The NOE handles are my preference. RCBS is probably second. The MP handles are...
    9 replies | 305 view(s)
  • Guardian's Avatar
    01-21-2021, 03:59 PM
    Guardian replied to a thread Getting into Swaging in Swaging
    I ain't BTS, but I'll save you some waiting: http://castboolits.gunloads.com/showthread.php?118083-Custom-BTSniper-40-cal-one-step-dies http://castboolits.gunloads.com/showthread.php?70121-40-cal-from-9mm-easiest-by-far-and-cheap! Enjoy!
    16 replies | 904 view(s)
  • Guardian's Avatar
    01-19-2021, 12:46 PM
    Also consider that a good portion of your prospective market are folks who: A) will lose interest in reloading as soon as ammo returns to shelves, or B) will be restricted by primer availability.
    37 replies | 1199 view(s)
  • Guardian's Avatar
    01-13-2021, 04:23 PM
    That's unfortunate! I ordered two moulds from MP Monday and had them by Friday. I can't even get stuff from within the US that quick! Some brass that was sent to me left Anderson, SC (196 miles or 3.5 hours away); came to K-town (30 miles from...
    28 replies | 1519 view(s)
  • Guardian's Avatar
    01-12-2021, 09:07 PM
    I looked at the Master Pot again tonight and realized I was wrong. It is possible to change the side the operating handle is on.
    24 replies | 738 view(s)
  • Guardian's Avatar
    01-12-2021, 03:51 PM
    I've found that if you use a wrench to actually seat the bushing into the receiver, it doesn't rotate out. However, I don't like having to grab a wrench every time, so a short piece of 12 GA copper wire that hooks on the lower peg of the powder...
    51 replies | 1053 view(s)
  • Guardian's Avatar
    01-12-2021, 12:43 PM
    I've got a Magma Master Pot. Its the only pot I've ever owned, so I can't compare it to anything. I'm of the mindset that I'm too poor to own cheap tools. I can't afford to keep replacing them. I also understand that good tools make work easier....
    24 replies | 738 view(s)
  • Guardian's Avatar
    01-06-2021, 04:50 PM
    I used a Forster power trimmer base and a WFT in the chuck on a benchtop drill press for a while. Two issues I ran into were: 1-inconsistent trim lengths due to the expander ball in the sizing die pulling the shoulder longer when the case was...
    42 replies | 1333 view(s)
  • Guardian's Avatar
    01-06-2021, 04:34 PM
    Yep. Drop it into an empty magazine and make a mark on the rod with a sharpie and you'll know before it runs out. If you want a 5 primer heads-up and ain't good at spacial relations, put 5 primers in the magazine and draw another line. Repeat for as...
    68 replies | 2738 view(s)
  • Guardian's Avatar
    01-06-2021, 04:28 PM
    My first question is, do you like the reloading process? Second is why do you think you want to go progressive? I love the process of reloading! I like it as much as I do shooting. I made the jump to progressive because I am a tool junkie and...
    68 replies | 2738 view(s)
  • Guardian's Avatar
    01-06-2021, 01:18 PM
    I also use this method, but measure by the cap on the mineral spirits can. I put two caps full in while the tumbler is running, then add the NuFinish. I let it run a few seconds and then dump the brass in. Also using corn cob media from Grainger. I...
    31 replies | 920 view(s)
No More Results
About Guardian

Basic Information

About Guardian
Location:
In the Hills of Tennessee

Signature


WANTED: CH AutoChamp Mark IV, V, or Va - PM me if you've got one you'd like to part with.

Statistics


Total Posts
Total Posts
351
Posts Per Day
0.12
Albums
Total Albums
1
Total Photos
33
General Information
Last Activity
Yesterday 08:23 PM
Join Date
01-24-2013
Referrals
0

1 Friend

  1. Tom_Highway Tom_Highway is offline

    Boolit Bub

    Tom_Highway
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check