MidSouth Shooters SupplyRotoMetals2Inline FabricationGraf & Sons
StainLess Steel MediaTitan ReloadingLee PrecisionADvertise here

Tab Content
  • RCE1's Avatar
    03-11-2018, 10:34 PM
    If you don't get the feeling it's a hard, gritty, creepy trigger, it's probably been lightened.
    17 replies | 332 view(s)
  • RCE1's Avatar
    03-07-2018, 10:19 PM
    RCE1 replied to a thread Movie: Wind River in Our Town
    I liked the movie a lot and think they did a very good job getting the guns right. I did notice, however, that there was a sleeve of rifle cartridges on the buttstock of his shotgun in one scene, but it didn't last long. Have to nit pick, though. ...
    26 replies | 852 view(s)
  • RCE1's Avatar
    03-04-2018, 06:26 PM
    I hate to be negative, but when I saw the first posting in this thread, I was wondering how you were going to enjoy that rifle. It's pretty and I actually like Pedersolis, but the .45/120 is not for beginners. I've never known anyone who got one to...
    32 replies | 929 view(s)
  • RCE1's Avatar
    03-02-2018, 01:15 PM
    RCE1 replied to a thread Pro Melt 2 update in Casting Equipment
    From my experience, temperatures don't change that fast until you add a bunch of cold lead, then it gets slow again while it heats back up. Some run two pots, one to cast with and one to pre-heat the melt so you don't get the wide temperature...
    3 replies | 239 view(s)
  • RCE1's Avatar
    02-28-2018, 11:08 PM
    That looks like fun. I've done 1885 Winchesters, Borchardts, Ballards and Martinis, but never a roller. Those Swedish actions are a nice place to start. I like that cartridge, too.
    151 replies | 4570 view(s)
  • RCE1's Avatar
    02-28-2018, 10:18 PM
    Plastic pellets. I got mine in the sewing section of my local WalMart.
    31 replies | 686 view(s)
  • RCE1's Avatar
    02-28-2018, 03:15 PM
    I just installed mine into a Hornady Lock N Load bushing. Works great even upside down, the way it's supposed to be threaded in.
    7 replies | 217 view(s)
  • RCE1's Avatar
    02-25-2018, 02:39 PM
    I thought I'd try this system out on my new-ish Lee Classic Cast O-ring press. It's a perfect fit and seems to work pretty well, but I was wondering what one would use as a wrench to tighten it down without marking it up. I put an RCBS die in one...
    3 replies | 153 view(s)
  • RCE1's Avatar
    02-24-2018, 02:09 PM
    I like the clear as well, although I've been throwing a little black in with it.
    401 replies | 240020 view(s)
  • RCE1's Avatar
    02-16-2018, 04:13 PM
    I melted the first three test runs with my thrift shop toaster oven. Thermostat sits right at 300, polymer melts after 2-3 minutes and I take it out at 10. If I go to 350 on the thermostat, I get melted bullets. Funny, though, was that the...
    20 replies | 998 view(s)
No More Results
About RCE1

Basic Information


Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
Yesterday 05:33 PM
Join Date
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check