Inline FabricationMidSouth Shooters SupplyADvertise hereTitan Reloading
Lee PrecisionRotoMetals2Repackbox

Tab Content
  • Mitch's Avatar
    01-16-2021, 09:32 PM
    coast of drills.min wage for you time.and being realy mad.$ 52.50 is looking good.I feel your pain proly is good we can't just go buy the C4
    17 replies | 398 view(s)
  • Mitch's Avatar
    01-16-2021, 09:13 PM
    Great news
    20 replies | 486 view(s)
  • Mitch's Avatar
    01-16-2021, 04:46 PM
    If you pluged the bottom holes and are still geting lube under the bullet you are still not deep enough with the bullet.or your plugs came out.For the heat you only need to be warm to the touch Maybe 100 deg or so.It took me a long time to get the...
    20 replies | 486 view(s)
  • Mitch's Avatar
    01-16-2021, 04:21 PM
    For me it is try not to buy more lead or guns.Get the 2 dillon presses I hvae had for about a year up and running a few more calibers.In general improve my loading equpment.With this comes Building a new bench and some cabinets for storing all the...
    18 replies | 1087 view(s)
  • NyFirefighter357's Avatar
    01-13-2021, 07:57 AM
    Warm those bullets to about 120F before you shake them then the HF powder will stick without BB's. That color coverage of that powder sucks but it will work. I didn't have black BB's and couldn't get a good coating with the HF powder so I tried my...
    25 replies | 683 view(s)
  • NyFirefighter357's Avatar
    01-07-2021, 10:37 PM
    This is what your bullets will look like with HF white, the clear covers but the color is scarce. All tumbled in HF double tumbler This is what Smokes white & other colors look like
    19 replies | 589 view(s)
  • NyFirefighter357's Avatar
    01-02-2021, 07:51 AM
    OK, back to the grease. Do you not want to try the needle adapter? They come in many tip sizes. What about adapting a brass or aluminum block or pipe nipple to the outside of the tapered cap nipple? You can adapt any grease fitting the block or you...
    123 replies | 4808 view(s)
  • NyFirefighter357's Avatar
    01-01-2021, 09:18 PM
    I wet tumble rust/dirt off of tools & such.
    8 replies | 441 view(s)
  • NyFirefighter357's Avatar
    12-30-2020, 08:01 AM
    I have 3 broken models of those, V-1 is 14, V=2 is 13 & V-3 is 11 no matter how much money, food or electronics I invest in them they never seem to work! I found a better model only 50ft away, it's a newer model V-4 is 9. V-4 is a muti-use unit, ...
    16 replies | 519 view(s)
  • Mitch's Avatar
    12-29-2020, 11:48 PM
    Mitch replied to a thread Lead pipes in Lead and Lead Alloys
    Most lead pipe is pure lead or very close to it.There may be some Joints that have alot of solder in them to to you could have some tin in the mix if there are some solder joints.It should scratch eazy with the thumbnail. Be carefull of trapped...
    16 replies | 937 view(s)
  • NyFirefighter357's Avatar
    12-28-2020, 08:11 AM
    http://castboolits.gunloads.com/showthread.php?413219-Tumbler-died-Move-to-Ultrasonic
    4 replies | 238 view(s)
  • NyFirefighter357's Avatar
    12-26-2020, 01:04 AM
    Test them with a drop or two of muriatic acid to see if Zn is in the alloy, besides that I'd bet they are a mix of wheel weights. The rust isn't from the ingot it's from how/where it was stored. Despite what people say lead doesn't hold moisture &...
    24 replies | 1223 view(s)
  • NyFirefighter357's Avatar
    12-23-2020, 07:59 AM
    When I search CL I use several key works one at a time. Sinkers, reloading, fishing, hunting, solder, shooting, pewter, lead (but this gets you more leaded crystal glass than anything else.) Lead ingots run $2-$4 lb or more on CL here. But I did...
    14 replies | 917 view(s)
  • NyFirefighter357's Avatar
    12-21-2020, 07:51 AM
    If your going to try a grease gun and can't get the nipple off try a needle nose grease tip held tightly into that nipple. You can get them at any auto parts store and they come in different sizes. https://images.app.goo.gl/GQuEzdhZZhcESpfm7 ...
    123 replies | 4808 view(s)
No More Results
About Mitch

Basic Information

About Mitch
Location:
North West Ohio
Interests:
Beekeeper,Ham radio
Occupation:
Tool & Die Maker

Statistics


Total Posts
Total Posts
612
Posts Per Day
0.21
General Information
Last Activity
01-17-2021 02:25 PM
Join Date
12-03-2012
Referrals
0

4 Friends

  1. FlintsNSticks FlintsNSticks is offline

    Boolit Mold

    FlintsNSticks
  2. NyFirefighter357 NyFirefighter357 is offline

    Boolit Master

    NyFirefighter357
  3. rob g rob g is offline

    Boolit Mold

    rob g
  4. Yard5429 Yard5429 is offline

    Boolit Mold

    Yard5429
Showing Friends 1 to 4 of 4
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check