Titan ReloadingWisconsin TriggerRotoMetals2StainLess Steel Media
Graf & SonsMidSouth Shooters SupplyLee PrecisionInline Fabrication

Tab Content
  • farmerjim's Avatar
    Today, 07:19 AM
    farmerjim replied to a thread Ultrasonic Cleaners in Our Town
    I have the Harbor Freight one. I bought it to clean scuba regulators. I tried it for cleaning brass with citric acid and dish soap. It does a fair job of cleaning the inside of the case and primer pockets. I have used it to clean tens of thousands...
    8 replies | 112 view(s)
  • farmerjim's Avatar
    Yesterday, 07:34 PM
    farmerjim replied to a thread Resizing the 9mm?? in Cast Boolits
    +1 on lube even with carbide dies. I use just a dab of hornady one shot, if out I use lanolin.
    25 replies | 314 view(s)
  • farmerjim's Avatar
    04-24-2017, 09:39 AM
    RCBS hand prime (not universal) It's fast and easy.
    53 replies | 1077 view(s)
  • farmerjim's Avatar
    04-23-2017, 04:20 PM
    Easy. Hone it out with some emery cloth wrapped on a piece of wood dowel with a middle split cut in it. Spin it with a drill. It will take less than a minute. Test it every 20 to 30 seconds. Polish with extra fine before it is too big. I have done...
    6 replies | 288 view(s)
  • farmerjim's Avatar
    04-22-2017, 09:06 AM
    Try Amazon https://www.amazon.com/Gallon-N-methyl-2-pyrrolidinone-N-Methyl-Pyrrolidone-Stripper/dp/B00H7JTQXO
    11 replies | 462 view(s)
  • farmerjim's Avatar
    04-20-2017, 09:59 AM
    I have 2 of the 6 cavity molds and use both when casting. This is my most used boolit. I powder coat or Hi-Tek it. I size to .357 and use it in all my 9mm. I size it .359 and use it in my 38sp, 357 mag, and 357 max. I am told that it works good in...
    22 replies | 669 view(s)
  • farmerjim's Avatar
    04-18-2017, 05:31 PM
    I just picked my first 2 tomatoes of the year. April 18 beats my old early 1st tomato record of April 27. I planted these tomatoes on Feb 15 and kept them covered for 4 weeks.
    300 replies | 13086 view(s)
  • farmerjim's Avatar
    04-18-2017, 02:24 PM
    1/8 inch guard on clipper all over. Mirror to trim beard.Wife does my neck without guard.
    107 replies | 2822 view(s)
  • farmerjim's Avatar
    04-13-2017, 09:44 AM
    I have the B&D 40V one. It works great.
    14 replies | 503 view(s)
  • farmerjim's Avatar
    04-09-2017, 07:42 PM
    I have 2ea 6 cavity lee 358-125-RF molds because I make so many of them. I cast with both at the same time, and cast a little over 800 per hour. I load them in 9mm, 38 sp, 357 mag, 357 Max. I have heard that they work fine in 380acp. I will try this...
    22 replies | 749 view(s)
  • farmerjim's Avatar
    04-09-2017, 01:07 PM
    farmerjim replied to a thread Oil Change in Our Town
    If you are going to trade it in and get a new vehicle at 100,000 miles, use the cheapest oil and change at 7 to 10 K. If you want to go 250,000 in it, use good oil, and change more often.
    85 replies | 2618 view(s)
  • farmerjim's Avatar
    04-07-2017, 12:53 PM
    About 22 inches tall.
    44 replies | 2340 view(s)
  • farmerjim's Avatar
    04-07-2017, 09:58 AM
    " plus an equal amount extracted from our employers" "Try paying the whole thing yourself for 35 years." You do pay the entire amount. Your employer has to consider all costs when they hire you. If they didn't have to pay your SS, they would pay...
    46 replies | 1862 view(s)
  • farmerjim's Avatar
    04-01-2017, 07:26 PM
    I have had mine for over a year, have cast about 20,000 with it. It holds temp great. If you hold and pull your mold at an angle across the top of the mold guide, it works fine. I put a small LED light under the spout to give more light when casting.
    8 replies | 399 view(s)
  • farmerjim's Avatar
    04-01-2017, 07:03 PM
    I had 2 airguns before my first 22. 1. Red Rider BB gun. 2. Benjamin pump 22 pellet gun. Most people I know had these or more like them before the 22 RF.
    29 replies | 1165 view(s)
  • farmerjim's Avatar
    03-31-2017, 07:17 PM
    If I waited till Good Friday like my father said he was always told, I would be getting my tomatoes a month later than my normal time. I put my first planting in mid Feb. and I have tennis ball size tomatoes on the bushes already. Most of the...
    300 replies | 13086 view(s)
No More Results
About farmerjim

Basic Information

About farmerjim
St. Francisville, Louisiana


There is no difference between communism and socialism, except in the means of achieving the same ultimate end: communism proposes to enslave men by force, socialismóby vote. It is merely the difference between murder and suicide. Ayn Rand


Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
Today 07:26 AM
Join Date
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check