Inline FabricationMidSouth Shooters SupplyWidenersLee Precision
Titan ReloadingRotoMetals2RepackboxADvertise here

Tab Content
  • beemer's Avatar
    07-01-2020, 11:27 AM
    Years ago I had a SKS with that side mount, the rings were a steel band that tightened around the scope. It was an odd dia. so it was hard to get another scope to fit. The supplied scope wasn't much either. The rifle shot as well as any SKS I have...
    27 replies | 515 view(s)
  • beemer's Avatar
    06-22-2020, 01:01 PM
    beemer replied to a thread Old drills in Our Town
    The original cordless drill.
    22 replies | 703 view(s)
  • beemer's Avatar
    06-22-2020, 12:42 PM
    beemer replied to a thread Old drills in Our Town
    My Dad bought me a set of tools for Christmas when I was eight, that was in 1960. He hand picked the tools to make the set, they were good quality. I still have most of them except for what was stolen or worn out. One was a Stanley hand drill, I use...
    22 replies | 703 view(s)
  • beemer's Avatar
    06-09-2020, 10:17 PM
    I had one years ago, I carried in a sweaty hip pocket. The only problem was that the ammo would draw moisture and cause misfires in just a couple days. There were no problems with the gun itself. I thought later that maybe a 22 mag would have been...
    23 replies | 1266 view(s)
  • beemer's Avatar
    06-09-2020, 09:41 PM
    beemer replied to a thread Powder scale... in Reloading Equipment
    I have one oil dampened and two magnetic, none are of the current crop. When compared to each other all were acceptably close. I would use either one with no problems. Altogether I have 5 and the red Hornady is on the bench.
    14 replies | 520 view(s)
  • beemer's Avatar
    06-09-2020, 01:46 PM
    I worked building high end dinning room furniture for many years. The lead guys always checked our rulers against each other's or against a known source. Some of the lumber we used was VERY expensive and we need a reference point, we couldn't afford...
    56 replies | 2003 view(s)
  • beemer's Avatar
    06-08-2020, 11:44 AM
    I have bored several, I have a 3/8 bit that I made for my ML ramrods that is 44" long. A shorter one would work better but that's what I have. The extra length is supported with guide blocks made for each job. Every thing is lined up and leveled on...
    13 replies | 486 view(s)
  • beemer's Avatar
    06-03-2020, 08:45 PM
    beemer replied to a thread O-ring size in Casting Equipment
    I bought few #15 's, 1"O.D.- 3/4" I,D.- X 1/8. They are just a little tight but sealed my Lyman 450 pump piston just fine. Dave
    19 replies | 1746 view(s)
No More Results
About beemer

Basic Information

About beemer
Location:
Brushy Mountains of NC

Statistics


Total Posts
Total Posts
832
Posts Per Day
0.17
General Information
Last Activity
Today 10:07 AM
Current Activity
Viewing Forum CB Loads, Your Favorite Cartridge
Join Date
01-20-2007
Referrals
1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check