WidenersRepackboxMidSouth Shooters SupplyRotoMetals2
StainLess Steel MediaLee PrecisionGraf & SonsInline Fabrication
Titan Reloading
Tab Content
  • beemer's Avatar
    10-14-2018, 08:17 PM
    I posted this a while back but this looks like it might fit here. The load is 6 grains of Unique, standard CCI small pistol and a LEE 158 SWC GC with Lee tumble lube in a 357 case. I fired a cylinder from three Security Sixes across the Chrony. I...
    35 replies | 2007 view(s)
  • beemer's Avatar
    10-14-2018, 06:55 PM
    beemer replied to a thread A bit too hard lol in Cast Boolits
    I am not sure what to call it but I have a bucket of permanent type letters, it's hard. A bullet poured in a 140 gr. mold weights 125 grs. I poured a few for my 303 Brit but they broke off at the case mouth when they started up the feed ramp. The...
    8 replies | 348 view(s)
  • beemer's Avatar
    10-14-2018, 02:06 PM
    beemer started a thread Touch hole liner in Muzzleloading.
    I was reading the thread about Touch Hole Woes and have a question. The breach plug was notched where the flash hole entered the breach. I have built several cap locks and always set my own plugs and got a good fit. The only flint I have built I set...
    2 replies | 138 view(s)
  • beemer's Avatar
    10-12-2018, 07:12 PM
    I can tell you for certain that a 303 Brit will scatter parts of a Chrony all over the yard.
    6 replies | 440 view(s)
  • beemer's Avatar
    10-10-2018, 12:06 PM
    I think some can tell time also. I kept my step daughter's cat when she and my wife were gone for a week. After the first day he would wake me five min. before the clock went off and set on the bed and meow right before the time I usually went to...
    29 replies | 1344 view(s)
  • beemer's Avatar
    10-07-2018, 11:01 PM
    I have had the Bonanza for years and love it, my main press. Does it have the priming parts, that would be the hardest to find if missing. Standard shell holders will fit but the priming hole is different as the priming post are not the same...
    3 replies | 474 view(s)
  • beemer's Avatar
    10-05-2018, 11:18 PM
    beemer replied to a thread Copperheads in Our Town
    Copperheads come into this world with a bad attitude. We have them around here, I don't walk in the yard after dark without a light. Some people don't want snakes killed, guess they don't have to look at the doorstep before stepping out in the...
    38 replies | 1239 view(s)
  • beemer's Avatar
    10-01-2018, 11:07 AM
    beemer replied to a thread Big Bore Regret..? in Leverguns
    I have been on a search for a lighter load for my 1895SS for a while now. I have the Lyman that was designed for the Marlin, 410 grs. or so and the Lee 340. Never found a load that shot well with the 340 but the Lyman does well. I have been working...
    40 replies | 1582 view(s)
  • beemer's Avatar
    09-28-2018, 10:09 PM
    I made an expander for the same set for a buddy. Nothing special, just a good bolt with the right threads. Leave oversize and polish. I cut the head off and cut a slot for a screwdriver. He ended up with a .383 bullet also, if I remember...
    42 replies | 1293 view(s)
  • beemer's Avatar
    09-27-2018, 09:32 PM
    I have had three and wish I had kept them, all were reliable and close to poa. One was stolen and it was the one that my Father gave me, it was the most accurate snub I have ever owned. I always liked the lockup, latched at both ends.
    17 replies | 564 view(s)
  • beemer's Avatar
    09-25-2018, 07:22 PM
    beemer replied to a thread lee collet dies in Reloading Equipment
    The collet die works the neck of the case less than a conventional die. The necks are not sized to small and then opened up to the proper diameter, just sized to the mandrel. I did have one that did not size the neck enough, I just polished the...
    17 replies | 554 view(s)
  • beemer's Avatar
    09-25-2018, 07:00 PM
    Like Blanket, I immediately thought of the heat-powered fans. They are not cheap, but I'd expect their low number of moving parts would tend towards long life. If I heated with wood I would pony up for one since it can operate without power in a...
    31 replies | 811 view(s)
  • beemer's Avatar
    09-25-2018, 02:52 PM
    beemer replied to a thread 8 x 57 in Military Rifles
    Thanks guys, I'm going to give it a shot. Dave
    4 replies | 458 view(s)
  • beemer's Avatar
    09-23-2018, 05:25 PM
    beemer started a thread 8 x 57 in Military Rifles
    Not sure where to ask this but I have J word question, if this is the wrong place please move it. I have a scoped Yugo 48 Mauser and a supply of Remington 185 gr, core-lock bullets, there is no load data for this one that I can find. I can...
    4 replies | 458 view(s)
  • beemer's Avatar
    09-19-2018, 09:58 PM
    beemer replied to a thread Whole Home Generator in Our Town
    Propane service around here is a joke. Several years ago the company delivered propane to me, my Mom and brother, all within spitting distance from each other. One was $2.75, one $3.00 and mine was $4.25, called and got a runaround. The next year...
    68 replies | 2147 view(s)
  • beemer's Avatar
    09-18-2018, 08:22 AM
    I traded for an almost new 17 about 30 years ago, still have it box and all. Being a revolver guy I looked at it sideways for a while but finally realized what it was. It is a simple to operate and reliable fighting pistol. I have not poured...
    46 replies | 1424 view(s)
No More Results
About beemer

Basic Information

About beemer
Location:
Brushy Mountains of NC

Statistics


Total Posts
Total Posts
685
Posts Per Day
0.16
General Information
Last Activity
Today 08:39 AM
Join Date
01-20-2007
Referrals
1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check