ADvertise hereRepackboxTitan ReloadingMidSouth Shooters Supply
Lee PrecisionRotoMetals2Inline Fabrication

Donate Now Goal amount for this year: 6000 USD, Received: 6135 USD (102%)
OUR GOAL HAS BEEN MET!
Our Annual server fund drive is going on now! This donation drive helps fund Cast Boolits for an entire year, and helps support our 2nd amendment rights! You can donate by Paypal by clicking the DONATE button. Or by Cash / Check / MO to the address below:

Willy Snyder
PO Box 2732
Pocatello, ID 83206
****Due to overwhelming e-mails, I will be very slow in updating this list. Please bear with me!****


  • nicholst55's Avatar
    09-20-2019, 12:44 AM
    I worked on a large number of those military M1200s back in the day, and rather hated them at the time. IMHO, the Mossberg (or 870) is easier to work on. Maybe not as durable, but then the trigger mech of the 1200 always gave us fits.
    17 replies | 456 view(s)
  • nicholst55's Avatar
    09-19-2019, 11:41 PM
    Heck yeah! 8-) Which makes the entire exercise, on the part of the administrators, totally pointless - when the hackers and scammers can simply do the same thing. Yup, absolutely.
    9 replies | 432 view(s)
  • nicholst55's Avatar
    09-19-2019, 07:15 PM
    A guy on the FAL Files built one several years ago. He seems to like it. I've seen rifles advertised in .35 Whelen and .338 Win Mag, too. I think that a Garand in either .35 Whelen or 9.3X62mm would be a neat one.
    21 replies | 763 view(s)
  • nicholst55's Avatar
    09-19-2019, 07:03 PM
    The free solution to that is to install the lock ring on the bottom of the toolhead, rather than the top. Newer Lee dies are made slightly longer, to eliminate this problem.
    30 replies | 629 view(s)
  • nicholst55's Avatar
    09-19-2019, 06:52 PM
    Joined in 2007 (sure seems like it was longer ago than that), been here in South Korea since 2016, working for the U.S. Army. Went to log on yesterday and my IP address has been banned. After three years. And four years here from 2008-2012 -...
    9 replies | 432 view(s)
  • nicholst55's Avatar
    09-15-2019, 10:25 PM
    Triggers advertised for the TC Hawken will drop right in, also. I have a Davis double set that was advertised for a TC, that I installed in a Lyman/Investarms rifle, and it works perfectly.
    6 replies | 277 view(s)
  • nicholst55's Avatar
    09-10-2019, 09:04 AM
    Do what the Army does. Buy VCI Barrier Paper and make storage bags. Wipe the guns down, then vacuum seal them in the VCI bags. They should be good for several years that way. I deal with these nearly every day, and they DO work. Alternately,...
    26 replies | 946 view(s)
  • nicholst55's Avatar
    09-09-2019, 08:43 PM
    nicholst55 replied to a thread What drill sizes? in Our Town
    I remember reading an article about modifying .45-70 brass to accept 209 shotshell primers many, many years ago in HANDLOADER magazine - back before it became just more grocery store pap. The intent was to get a better propellant burn, IIRC. The...
    25 replies | 16036 view(s)
  • nicholst55's Avatar
    09-06-2019, 12:51 AM
    I bought several Czech made M98/22 Mausers that were built for the Turks for $50-60 from the distributor about that time. They ranged from pretty decent condition to downright ratty. One that I bought had an absolutely new barrel, another had a...
    32 replies | 1258 view(s)
  • nicholst55's Avatar
    09-03-2019, 09:10 PM
    I worked for MATCO Tools for a few years, and generally liked the quality of their tools (at that time, anyway). The problem with Snap-On/MATCO/MAC, etc. screwdriver bits is that their selection is pretty limited. No thin slot bits, for example. ...
    24 replies | 1118 view(s)
  • nicholst55's Avatar
    09-01-2019, 07:28 PM
    If you're working with a heavy recoiling (big-bore) Bisley-gripped revolver, JRH Advanced Gunsmithing does a very nice grip modification that increases the clearance between the trigger guard and grip frame. It necessitates custom grips afterwards,...
    26 replies | 885 view(s)
  • nicholst55's Avatar
    08-31-2019, 11:54 PM
    Has anyone recovered slugs fired through a lengthened forcing cone? Just wondering if they show less distortion of the nose?
    45 replies | 2152 view(s)
  • nicholst55's Avatar
    08-23-2019, 09:24 PM
    Your rifle has an aftermarket cast receiver and was assembled with milsurp parts by a firm in California. Quality varies from acceptable to downright scary. The serial number range associated with 'low number' receivers is irrelevant to your...
    35 replies | 1698 view(s)
No More Results
About nicholst55

Basic Information

Age
63
About nicholst55
Biography:
Retired Army Ordnance, former defense contractor
Location:
Daegu, Korea
Interests:
Reloading, tinkering, shooting
Occupation:
DA Civilian

Signature


Service members, veterans and those concerned about their mental health can call the Veterans Crisis Line to speak to trained professionals. To talk to someone, call 1-800-273-8255 and Press 1, send a text message to 838255 or chat at VeteransCrisisLine.net/Chat.

If you or someone you know might be at risk of suicide, there is help. Call the National Suicide Prevention Lifeline at 1-800-273-8255, text a crisis counselor at 741741 or visit suicidepreventionlifeline.org.

Statistics


Total Posts
Total Posts
2,980
Posts Per Day
0.64
General Information
Last Activity
Today 04:52 AM
Join Date
01-12-2007
Referrals
0

2 Friends

  1. 1Shirt 1Shirt is offline

    Boolit Grand Master

    1Shirt
  2. Bob Krack Bob Krack is offline

    Boolit Master at Heavens Range

    Bob Krack
Showing Friends 1 to 2 of 2
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check