RotoMetals2Inline FabricationADvertise hereRepackbox
Titan ReloadingLee PrecisionWideners

  • Alferd Packer's Avatar
    02-26-2020, 03:26 PM
    You can corral that brass if you take time to cobble together a brass catcher. Using wire coat hanger wire and the plastic mesh they package onions in. Bend the wire like the wire flyswatters handle. Then bend the leftover wire shaped like an...
    12 replies | 978 view(s)
  • Alferd Packer's Avatar
    02-24-2020, 01:18 PM
    Would it be out of line for me to ask what was the results of the comparison test? Were the originals any good or as good as the ones that Harris made. I make these myself and I know the ones Harris makes work very well. I never came across any...
    6 replies | 1416 view(s)
  • Alferd Packer's Avatar
    02-24-2020, 08:37 AM
    Only to a recoil junkie.
    30 replies | 1781 view(s)
  • Alferd Packer's Avatar
    02-18-2020, 07:41 PM
    Some are Bullseye shooters. Some are plagued by inaccurate firearms and can't seem to hit anything. It's just the fault of those pesky firearms!
    24 replies | 871 view(s)
  • Alferd Packer's Avatar
    02-15-2020, 07:28 PM
    I shoot primer propelled wax bullets. They can be shot from an automatic but they must be single loaded. Shooting these at paper will really help. Also if you reload. You can load up some minimum loads using lighter weight recommended bullets.
    82 replies | 63519 view(s)
  • Alferd Packer's Avatar
    02-15-2020, 07:15 PM
    ATF and kerosene Also power steering fluid and kerosene May be same stuff in ATF and power steering fluud.
    96 replies | 15981 view(s)
  • Alferd Packer's Avatar
    02-15-2020, 01:58 PM
    I make coffee every morning. I dump the grounds on newspaper and they are dried out by the next day. I save them up in an empty coffee can and use them for my shot loads. They blast the carpenter bees and wasps and unlike the loads that use grits...
    59 replies | 13773 view(s)
  • Alferd Packer's Avatar
    02-14-2020, 12:43 PM
    Old thread, but lighter fluid, mineral spirits , and even gasoline will soften and dissolve wax bullet residue pretty easy and quick. Using it on a bore brush, it goes faster, then change to patches. Easy peasy.
    25 replies | 10431 view(s)
  • Alferd Packer's Avatar
    02-14-2020, 01:31 AM
    Good for you! I always like to hear the scoffers getting educated!
    13 replies | 585 view(s)
  • Alferd Packer's Avatar
    02-11-2020, 05:19 AM
    Some of us just like to shoot. Others like to get more hands on and make the pellets and ammo. This is a cast boolit forum also.
    17 replies | 10782 view(s)
  • Alferd Packer's Avatar
    02-11-2020, 04:38 AM
    You have to use a hot plate to bring your mould up to heat and then your pellet mould will fill out.And keep the pellet mould hot in between casts to maintain temperature. In fact I use the hot plate to bring all hollow point molds and pins up to...
    13 replies | 800 view(s)
  • Alferd Packer's Avatar
    02-10-2020, 06:33 PM
    Thanks guys. I enjoyed reading these thoughts on .303. I have the LEE six cavity 90 gr tumble lube swc. The darn thing has always thrown bullets .321. Not supposed to, but I always have to size them down all but erasing the tumble lube lines...
    21 replies | 2824 view(s)
  • Alferd Packer's Avatar
    02-07-2020, 09:33 PM
    Open the ends of a cardboard box and throw a blanket over it. That breaks up the noise too when you shoot catsneeze load thru keeping rifle inside. You can put some straw on bottom of box and on sides inside. Finns used this trick against the...
    35 replies | 3527 view(s)
  • Alferd Packer's Avatar
    02-07-2020, 03:22 PM
    Don't forget those hot glue bullets that are primer powered. They are fun loads too. They can have a bit of lead added and a grain of Bullseye or any fast powder and used for small game when they are cast using your larger size bullet mould....
    49 replies | 6737 view(s)
  • Alferd Packer's Avatar
    02-07-2020, 01:48 PM
    I believe any ammo loaded in a cold area must be kept in a cold area till it is shot. I believe moisture from condensation will form inside the shells and make your powder wet and damp if this ammo is brought into a heated area. The ammo companies...
    18 replies | 2163 view(s)
  • Alferd Packer's Avatar
    02-06-2020, 08:43 PM
    Used a dremel moto tool with a small mounted stone to polish/ grind the hole larger on the shell holders.Mine were hardened where the hole is and would dull a drill bit.
    59 replies | 5743 view(s)
  • Alferd Packer's Avatar
    02-06-2020, 05:48 PM
    I use home made dippers to fill in where the LEE dippers fall short for the load I want. I just weigh up the load I want and select an empty case that will hold the load. I dump the pre-weighed charge into the case with a funnel. Then I just...
    25 replies | 2161 view(s)
  • Alferd Packer's Avatar
    02-06-2020, 04:57 PM
    Alferd Packer replied to a thread What the floss? in Cast Boolits
    I found that instead of letting the lead flow directly into the sprue hole that just a little to one side of the sprue hole and make a bank shot of the stream into the hole makes a difference . First reduce the flow a little and then try it. It...
    15 replies | 1140 view(s)
  • Alferd Packer's Avatar
    02-06-2020, 11:00 AM
    After WW2, the Japanese exported cheap tin cap guns to the U.S. The caps included with them came on yellow colored paper rolls and were made of black powder. They had the distinctive sulphur smell and were louder than american Kilgore company...
    72 replies | 5915 view(s)
  • Alferd Packer's Avatar
    02-01-2020, 04:25 PM
    I use a card disk that I lay atop the wax before i press the shell down on it. When the primer fires, the blast hits the cardboard disk and pushes the wax out. The card disk is like a gas check and keeps the barrel cleaner much longer. YMMV One...
    24 replies | 6158 view(s)
  • Alferd Packer's Avatar
    02-01-2020, 04:09 PM
    Always push unprimed cases into wax. Only prime them after wax is in case. Otherwise trapped air is compressed and makes wax creep back out of case before you shoot. Wax bullet can stick out end of cylinder tying up gun. It happens, though not...
    24 replies | 6158 view(s)
  • Alferd Packer's Avatar
    01-31-2020, 03:46 PM
    I have NOE .25 pellet mould. I use it to cast pellets for primer powered loads in my .25 auto handgun. Just for fun! I can also add a half grain of Bullseye powder .
    13 replies | 800 view(s)
  • Alferd Packer's Avatar
    01-31-2020, 03:41 PM
    Alferd Packer replied to a thread RB in air rifles? in AirGuns
    I have the NOE 22 magnum mould with the extra pins to make a hollow base skirt, heavier than the swaged ones they sell. Then I can go heavier than that as the next shorter pin let's more lead in the cast pellet to make the skirt thicker. The next...
    14 replies | 644 view(s)
More Activity
About Alferd Packer

Basic Information

Statistics


Total Posts
Total Posts
237
Posts Per Day
0.08
General Information
Last Activity
Yesterday 02:03 PM
Join Date
06-22-2012
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check