Titan ReloadingRotoMetals2Inline FabricationLee Precision
WidenersADvertise hereRepackbox

Tab Content
  • cwlongshot's Avatar
    Today, 11:53 AM
    cwlongshot replied to a thread Henry .357 for deer in Leverguns
    I have dumped more than a dozen with a 170 GD and LilGun at 1750 FPS. Shot a few with a 140 Speer HP from a 8” Colt with H110. Recent years the 358429 170g Keith bullet and BlueDot drop deer dead inside 75 easily. I shared your Skepticism. Until...
    9 replies | 219 view(s)
  • cwlongshot's Avatar
    Today, 11:48 AM
    My favorite 357 Boolit!! I just got a 358429 HP after many years on and off looking!! (Same sane only HP). I also have had a 358429 2 cav for decades. My hunting load is with heavy charge of BlueDot. A stiff load but safe in my Gun’s. CW
    8 replies | 277 view(s)
  • cwlongshot's Avatar
    Today, 11:36 AM
    Something else to remember. It’s generally recommended 20/400. Meaning 20 AFTER bullets reach 400. NOT JUST 20 min in oven. CW
    57 replies | 2144 view(s)
  • cwlongshot's Avatar
    Today, 11:34 AM
    The ORIGINAL CAST BULLET LAUNCHER! ;) CW
    37 replies | 1872 view(s)
  • cwlongshot's Avatar
    Yesterday, 10:11 AM
    Go get another!! Try to make it a rescue you can help save another!! As I said the joys they bring cannot be measured. Here is a pic of my Roxy, doing what she does watching TV with me.
    42 replies | 520 view(s)
  • cwlongshot's Avatar
    02-19-2020, 07:56 PM
    Sorry to read this. Hate to read these actually. But part of life is death and none of us make it “out” alive. I dread the day. Have experienced it it’s never fun and the current is expected to be the worst. My first “lap dog” 19# Lahasa and my...
    42 replies | 520 view(s)
  • cwlongshot's Avatar
    02-19-2020, 07:51 PM
    I get same in one Marlin ‘94. My newer Cowboy dosent do it. So I agree generous chamber. I have shot some healthy RUGER loads pushing 300’s to 1600 to see it. Worst is brass probably won’t last as long. But I have had that rifle for over twenty...
    20 replies | 457 view(s)
  • cwlongshot's Avatar
    02-19-2020, 05:32 PM
    Well that’s a big one! My first attempt set at 400 left a pool of lead with a couple lumps. Ironically it was red HF and looked omanis. Temps on these cheap ovens can be all over the map
    57 replies | 2144 view(s)
  • cwlongshot's Avatar
    02-19-2020, 02:29 PM
    I like my 222/20 better than my later, bigger & heavier 223/20 Savage. That 222 is a earlier model and much lighter. Shoots great too regulation is MUCH closer than the 223/20. Not much difference as the 223 is a 1:14 so it won’t shoot heavier than...
    33 replies | 2140 view(s)
  • cwlongshot's Avatar
    02-19-2020, 02:17 PM
    Just called Keystone. (Not real happy with them.) Dispite the lip service they acknowledge the order but it’s not gonna ship till “possibly” end of this week. They say my dealer called up a few days after my order and ordered a stocking order. She...
    33 replies | 2140 view(s)
  • Ramson222's Avatar
    02-19-2020, 01:32 PM
    Sand in a chamber would be a very bad thing.
    30 replies | 550 view(s)
  • cwlongshot's Avatar
    02-19-2020, 07:37 AM
    You should not be seeing leading. What’s the dia? Hardness with PC at sub 1k is moot. I have shot dead soft to straight Lino PCd zero issues multiple Glock bbls. Are you crimping heavily? Said before but your sure the PC is cured...
    57 replies | 2144 view(s)
  • cwlongshot's Avatar
    02-19-2020, 07:34 AM
    I loaded my oven with lava rock. It helps allot with even heat but needs to be warmed. So I run the oven full timer before first bake. I keep two baskets on top and warm bullets in there before coating. It absolutely helps! My bullets make it just...
    24 replies | 390 view(s)
  • cwlongshot's Avatar
    02-18-2020, 09:06 PM
    cwlongshot replied to a thread Marlin 1894 to???? in Leverguns
    EXACTLY MY THOUGHTS!! Find a smith to spin off that 43 Bbl and install and chamber a 357 barrel. First on your block to have a B&D!! Great caliber!! CW
    19 replies | 549 view(s)
  • cwlongshot's Avatar
    02-18-2020, 09:00 PM
    Either of those colors has worked for me either. Some colors simply don’t work shake n bake. I bought two last week green and blue. Blue has always been great for me. But never bought this brand. Wouldn’t coat at all. Left a “frosted” look. But...
    24 replies | 390 view(s)
  • cwlongshot's Avatar
    02-18-2020, 03:53 PM
    Bottom line is 99% of distances where a red dot is used will not see an appreciable difference. Have t ya seen them mounted at a 45 angle on MSR setups? If it really bothers ya, you have a dot with a tube 1” or 30mm or a pic rail, levels are...
    16 replies | 508 view(s)
  • cwlongshot's Avatar
    02-18-2020, 05:15 AM
    Haha. Good deal.
    8491 replies | 775215 view(s)
  • cwlongshot's Avatar
    02-17-2020, 10:59 AM
    Something wrong with Accurate? I have three molds built by them and every one casts beautifully was shipped promptly and works as expected. Check out NOE maybe. I also have a 311440 that drops large enough and also shoots well for Me with...
    121 replies | 8567 view(s)
  • cwlongshot's Avatar
    02-17-2020, 06:18 AM
    wow!!
    8491 replies | 775215 view(s)
  • cwlongshot's Avatar
    02-16-2020, 09:02 PM
    Cleaning brass
    8491 replies | 775215 view(s)
  • cwlongshot's Avatar
    02-16-2020, 08:52 PM
    Two more “new” ones for me this week. Both RCBS. First is a 32-98 SWC and the second is a eBay find 45-300 FN. It’s covered in surface rust. But inside blocks is clean but one spot. Hoping evapo rust cleans them. CW
    270 replies | 39008 view(s)
  • Ramson222's Avatar
    02-16-2020, 07:14 PM
    My measurement were taken at the base of the bullet. I will be sending the mold back tomorrow.
    27 replies | 756 view(s)
  • cwlongshot's Avatar
    02-16-2020, 05:29 PM
    This mold is a Accurate 31-135s. It was designed expressly for the RUGER Single six to fit it’s shorter cylinder. I have t yet tried it in the 32/20 but I will soon! Froggy, 7.3 showed ever so slightly sticky extraction from the birds...
    121 replies | 8567 view(s)
  • Ramson222's Avatar
    02-16-2020, 07:22 AM
    I measured six random bullets the shank is .286 to .288 at the largest obviously .284 diameter gas checks are not going to fit.
    27 replies | 756 view(s)
  • cwlongshot's Avatar
    02-15-2020, 08:55 PM
    Hello Froggie Yes, your correct. I haven’t shot the birds-head with these kids yet. I have 6,6.5,7 & 7.3 g loads ready to try. This load started at 5.5g of Blue Dot. Then 5.8 & 6.0 gr. Then 6.5 and 6.8 and 7.0g. No issues with any. Cases...
    121 replies | 8567 view(s)
  • cwlongshot's Avatar
    02-15-2020, 06:45 PM
    cwlongshot replied to a thread 350 legend HP? in Cast Boolits
    I have a MP 359-220 HP mold that’s really showing promise. I just got a 358429 HP. It’s a lil lighter than what I want as a hunting bullet. I have tried a LBT 220 and a Lyman 358315 and RCBS 200-FN. none shot very well. Not well enough for...
    5 replies | 261 view(s)
  • cwlongshot's Avatar
    02-15-2020, 03:59 PM
    2485 replies | 1090063 view(s)
  • cwlongshot's Avatar
    02-15-2020, 03:54 PM
    I’m stoping at 7.3g with this 135g. No pressure but I broke 1250 and simply don’t “need” more. Shoots great. Tomorrow I’ll. Try them in the Birdshead. ;) CW
    121 replies | 8567 view(s)
  • cwlongshot's Avatar
    02-14-2020, 07:26 PM
    Big squirrel no doubt! UPDATE; STILL waiting on my Cricket. ;(. But I have spoken with the Keystone Factory four times and am holding hope that it’s either at my gun shop or will be tomorrow. Unbelievable it’s been such a hassle acquiring...
    33 replies | 2140 view(s)
  • Ramson222's Avatar
    02-14-2020, 07:02 PM
    Here is a pic of the problem, by the way the maker has offered to replace or fix the mold. Notice the burr around the base of the bullets.
    27 replies | 756 view(s)
More Activity
About Ramson222

Basic Information

About Ramson222
Location:
Douglas Ridge Rifle Club, Eagle Creek, Oregon
Occupation:
Acupuncturist

Statistics


Total Posts
Total Posts
206
Posts Per Day
0.07
General Information
Last Activity
Today 12:16 AM
Join Date
06-03-2012
Referrals
0

1 Friend

  1. cwlongshot cwlongshot is offline

    Boolit Master

    cwlongshot
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check