Lee PrecisionMidSouth Shooters SupplyStainLess Steel MediaGraf & Sons
Inline FabricationTitan ReloadingRotoMetals2ADvertise here

Tab Content
  • fstreed's Avatar
    05-19-2018, 10:39 PM
    I also like them. I've been buying from them since their complete line of products fit in a monthly flyer of a dozen or two pages, mostly comprised of bulk quantities of Remington and Win. bullets. I still have some boxes of 500 or 1M .357 and 9mm...
    3 replies | 245 view(s)
  • fstreed's Avatar
    05-15-2018, 07:11 PM
    That's too bad about Matilda. Some people...sheesh! I hope you didn't invite him for chicken and dumplings. :lol:
    32 replies | 1508 view(s)
  • fstreed's Avatar
    05-15-2018, 02:01 AM
    Lee 2 cavity molds are a cheap way to try out a particular bullet style, for example a truncated cone in 9mm to see if there are any chambering problems, before buying a high dollar mold. And the new style 2 cavs seem to work pretty well and make...
    43 replies | 946 view(s)
  • fstreed's Avatar
    05-12-2018, 03:48 AM
    Replaced the abused sprue plate screw with a 1/4 x 28 allen type cap screw with a wavey (spring) washer, put a small pellet of 10 Ga. copper wire under the lock screw, adjusted and seated it all in, works like a champ. I wanted a new slotted...
    10 replies | 325 view(s)
  • fstreed's Avatar
    05-10-2018, 03:59 AM
    I have neither, a situation I hope to correct in the not too distant future.
    43 replies | 946 view(s)
  • fstreed's Avatar
    05-10-2018, 03:53 AM
    Yes, I agree. I like the new Lee 2 cavity molds over the older ones. The alignment pins seem to work better for one thing. I have two of them now, one in .45 and one for 9 MM, they both drop nice round bullets. Some of the old style made oval shaped...
    43 replies | 946 view(s)
  • fstreed's Avatar
    05-06-2018, 12:59 PM
    Mine does have the set screw that locks the sprue plate screw in place. The plate screw is worn and battered where the set screw engages it. I think a replacement screw (1/4 x 28 fillister) will fix it. And I think I will take jsizemore's advice...
    10 replies | 325 view(s)
  • fstreed's Avatar
    05-05-2018, 10:59 PM
    I bought this mold, a 4 cavity, at a gunshow a couple of years ago. It had a lot of surface rust and some pitting, all on the outside. The cavities looked good and no rust on the faces of the blocks or anywhere that counts as important. I soaked it...
    10 replies | 325 view(s)
No More Results
About fstreed

Basic Information

Statistics


Total Posts
Total Posts
43
Posts Per Day
0.01
General Information
Last Activity
Today 01:37 AM
Join Date
12-31-2006
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check