StainLess Steel MediaLee PrecisionTitan ReloadingWisconsin Trigger
Graf & SonsMidSouth Shooters SupplyInline FabricationRotoMetals2

  • Boz330's Avatar
    Yesterday, 08:15 AM
    Boz330 replied to a thread Ordered a kit pistol in Muzzleloading.
    Nothing wrong with that group. Bob
    7 replies | 430 view(s)
  • Boz330's Avatar
    Yesterday, 08:11 AM
    Boz330 replied to a thread Oak Ridge TN in Muzzleloading.
    Rick Weber's e-mail; : Contact him to get on the e-mail list for the match next year. Applications go out in Jan IIRC. Bob
    8 replies | 187 view(s)
  • Boz330's Avatar
    Yesterday, 08:02 AM
    Boz330 replied to a thread Oak Ridge TN in Muzzleloading.
    Here is a match summary from the match director Rick Weber. I'll post his e-mail. 30 matches over 20 years, time does not do it justice as it's has just flown by. This year we were blessed with some great weather both days...
    8 replies | 187 view(s)
  • Boz330's Avatar
    03-27-2017, 10:00 AM
    Boz330 started a thread Oak Ridge TN in Muzzleloading.
    I just got back from the Mid and Long Range match at Oak Ridge. If you shoot a Gibbs rifle or LR ML you should give this match a shot. The distances are 200, 300, 600, and 1000yd. The match is geared toward the beginning LR shooter with generous...
    8 replies | 187 view(s)
  • Boz330's Avatar
    03-26-2017, 03:08 PM
    The pistol club that use to shoot on my farm, till we ran afoul of planning and zoning built these bermed ranges. First picture the range on the right allows 125yd. The rest are 25yd. There is a 300yd range on the right of the other 2 pictures. The...
    13 replies | 500 view(s)
  • Boz330's Avatar
    03-26-2017, 02:53 PM
    Unfortunately my chrono doesn't do SD but I would think that it would be that low if I did the calculations to get from the extreme spread to SD. Even with a calculator that is a lot of key punching. At least I feel like I'm headed in the right...
    47 replies | 1224 view(s)
  • Boz330's Avatar
    03-22-2017, 08:17 AM
    Boz330 replied to a thread Some leather in Special Projects
    I haven't tried to make the cartridge holders but have built a number of cheek risers. I have put retaining loops around the butt. Another thing that works pretty good is to put a piece of tool drawer liner under the leather. This stuff keeps tools...
    17 replies | 647 view(s)
  • Boz330's Avatar
    03-20-2017, 05:25 PM
    I finally got a chance to shoot a bunch of 62 gr 40-65 loads that I tried with and without neck tension and varying compression levels. Tried some 1.5F Kik as well as 2F OE. The Kik was quite a bit slower than the OE. The best 2 loads were OE with...
    47 replies | 1224 view(s)
  • Boz330's Avatar
    03-17-2017, 09:02 AM
    I had a friend bulged a barrel on a 38-50 and couldn't tell any difference in accuracy. I have a 38-40 with a slight bulge, you can feel it when cleaning but can't see it and it shoots fine. I also bulged a barrel on a 45 auto and didn't even know...
    28 replies | 784 view(s)
  • Boz330's Avatar
    03-11-2017, 03:01 PM
    I had a 357 mag done on a small action and the smith that did it specializes in Martinis and he wouldn't do it in Max, said the round was too long. Even the 357Mag has to have the lever lowered against the spring tension to get the round in the...
    38 replies | 1512 view(s)
  • Boz330's Avatar
    03-09-2017, 09:25 AM
    I shoot a 385gr LBT .460 boolit in mine. It was made for a Trapdoor. If you use 20-1 with BP the boolit will slug up to fit the bore. Smokeless not so much. This is what mine will do with that load. Bob
    38 replies | 1512 view(s)
  • Boz330's Avatar
    03-06-2017, 07:09 PM
    I gaged my powder with store bought. You have to also remember that the thickness of the wire in the screens makes a difference. Thick wire and 30 mesh could mean 4F. Powder making is like skinning a cat there is more than one way to do it and they...
    1601 replies | 331893 view(s)
  • Boz330's Avatar
    03-03-2017, 12:03 PM
    Try a finer powder. My guns shoot best with 3F. My 3F is what is held on a 30 mesh screen. This after it has passed a 16 mesh and 20 mesh. Bob
    1601 replies | 331893 view(s)
  • Boz330's Avatar
    03-01-2017, 10:00 AM
    BA, my birthday is the end of this month. Do you want me to PM you my address.;)
    38 replies | 1512 view(s)
  • Boz330's Avatar
    02-28-2017, 03:25 PM
    I have never seen a motor that fast on a household appliance. Usually a motor in that size would be 1750 or 3500 RPMs. Motors of that persuasion aren't that expensive. Bob
    19 replies | 705 view(s)
  • Boz330's Avatar
    02-28-2017, 03:17 PM
    Not knowing where you are, makes for problems. In the US Vic Samuels is a great resource. Here are 2 he has done for me. A 357mag without the scope, a 7mm Waters with the scout scope. The Waters shoots a dime size group at 100yd, haven't figured out...
    38 replies | 1512 view(s)
No More Results
About brady1013ax

Basic Information

About brady1013ax
New to BPCR. Having a blast with my God Father and hunting buddies.
Guns and Golf
IT Guy


Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
07-16-2014 02:37 PM
Join Date

1 Friend

  1. Boz330 Boz330 is offline

    Boolit Master

Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check