Graf & SonsLee PrecisionWidenersStainLess Steel Media
MidSouth Shooters SupplyRotoMetals2Titan ReloadingInline Fabrication
Tab Content
  • Larry Gibson's Avatar
    Today, 10:55 AM
    Larry Gibson replied to a thread Alloy for 44 Mag in Cast Boolits
    I suggest getting some tin (either ordering pure tin or find some solder or pewter locally). Mix the linotype with lead at 35% lino and 65% lead. Then add 2% tin to that. That should give you a close alloy comparable to old COWWs of yester-year. ...
    16 replies | 255 view(s)
  • MOA's Avatar
    Yesterday, 05:57 PM
    Tom, how do you go about doing the tumble lube with JPW. I'd like to try that on a few of my cast loads too.
    30 replies | 619 view(s)
  • MOA's Avatar
    Yesterday, 05:41 PM
    Advil, That's great news. I picked mine up from Eric back in 2011 or 2012 just can't remember for sure. So far so good on mine still working but should it stop at least due to your efforts and generosity in sharing this I will not only be able to...
    5 replies | 628 view(s)
  • MOA's Avatar
    Yesterday, 05:24 PM
    duplicate post sorry.
    29 replies | 1024 view(s)
  • MOA's Avatar
    Yesterday, 05:13 PM
    Good looking boolits there Barr. I see your top punch is doing what mine use to do....ring the top of the boolit. I went to a little larger top punch that still sat square on the boolit but was made for a larger diameter boolit to get away from the...
    29 replies | 1024 view(s)
  • MOA's Avatar
    Yesterday, 02:46 PM
    Jd9770, It's not a huge library of load data. I'm kind of a piker compared to a few member on this forum. I remember seeing one time someone's reload data that took up an entire wall from floor to ceiling. Must have been 20 or 30 times the size of...
    31 replies | 535 view(s)
  • Larry Gibson's Avatar
    Yesterday, 10:41 AM
    Good Idea.....only caveat I would suggest is to have a 14" twist and certainly not any faster twist than 12". Otherwise, with cast bullets, you lose accuracy with the 30-30 capacity that the additional gain in velocity would provide. If done just...
    30 replies | 619 view(s)
  • swheeler's Avatar
    01-20-2019, 06:12 PM
    I found this searching, looks like I have the original version... Join Date: May 2012 Location: USA Posts: 4,356 ExArmy11b will become famous soon enoughExArmy11b will become famous soon enough Older "One Ragged Hole" sights vs. new ones...
    55 replies | 1617 view(s)
  • MOA's Avatar
    01-20-2019, 03:32 PM
    You can never have enough in my book. (Pun intended ). :bigsmyl2:
    31 replies | 535 view(s)
  • swheeler's Avatar
    01-20-2019, 11:50 AM
    Yes I have one on RBH and Ruger SSix, I like them. I'm not sure they are made any longer though, One Ragged Hole was the name. The link above may be the same company with a slight name change for the sight?
    55 replies | 1617 view(s)
  • Larry Gibson's Avatar
    01-20-2019, 11:20 AM
    Larry Gibson replied to a thread 35 Rem Mauser in Military Rifles
    That's the barrel I used some years back to build my 35 Rem on a M91 Argentine action.
    23 replies | 991 view(s)
  • Larry Gibson's Avatar
    01-20-2019, 11:12 AM
    Larry Gibson replied to a thread 44-40 +p? in Leverguns
    Not criticizing any of your data, just would like to know for comparative analysis. Do you input any correction factor to offset the psi required to expand the cases? If not then does the instructions explain how that amount of psi is accounted...
    138 replies | 11117 view(s)
  • Larry Gibson's Avatar
    01-20-2019, 10:38 AM
    I have and use three Lee .308W collet sizers. One I use for 7.62x54R, one for loads using 7.62 LC match cases and one for using Winchester .308W cases. I also have Lee collet dies for a couple other cartridges. The Lee collet sizer certainly is...
    20 replies | 557 view(s)
  • MOA's Avatar
    01-20-2019, 10:04 AM
    MOA replied to a thread Casting for Glock17 in Cast Boolits
    Yes sir, that's just what I did in 2010 or 11, got two Wolf barrels for my 19's. The factory bbls have never seen cast. I've been running these RCBS 115 RN. So far my Gen 2 likes them ok.
    35 replies | 806 view(s)
  • MOA's Avatar
    01-20-2019, 09:40 AM
    Tru-dat, when you have a stack of these on the bench I always let someone fire a few if they desire. Amazing the look they have after the first round. 400 Jeffrey next to a ought six. :bigsmyl2:
    31 replies | 866 view(s)
  • MOA's Avatar
    01-19-2019, 09:09 PM
    I've got lots of books that span from the early sixties to current. But I too have started to use and look at what is online now. I also know that it could be offline just like that too. So, I went down to the local Wally and got myself about four...
    31 replies | 535 view(s)
  • MOA's Avatar
    01-19-2019, 08:48 PM
    MOA replied to a thread opinions please in Leverguns
    Well where it's a bit wet I like a stainless lever. And I think if you can find a Marlin XLR in 45-70 you have half the battle done. Low mount scope IF you want it scoped, not a light rifle, but not a very heavy one either. It does come with Ballard...
    17 replies | 307 view(s)
More Activity
About ShooterAZ

Basic Information

About ShooterAZ
Flagstaff, AZ


Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
Today 01:14 PM
Current Activity
Viewing Thread Two year old Apple Juice
Join Date

4 Friends

  1. Larry Gibson Larry Gibson is offline

    Boolit Grand Master

    Larry Gibson
  2. Lizard333 Lizard333 is offline

    Boolit Master

  3. MOA MOA is offline

    Boolit Master

  4. swheeler swheeler is offline

    Boolit Master

Showing Friends 1 to 4 of 4
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check