MidSouth Shooters SupplyRotoMetals2ADvertise hereInline Fabrication
Graf & SonsTitan ReloadingStainLess Steel MediaLee Precision

Tab Content
  • Larry Gibson's Avatar
    Yesterday, 10:38 PM
    Put the target out. Put the firearm up on a bench rest using a solid rest of sand bags. Line up the sights on the center of the target paper and leave the firearm resting on the bags lined up. If the firearm is not zeroed then zero before putting...
    11 replies | 178 view(s)
  • Larry Gibson's Avatar
    Yesterday, 10:24 PM
    What weight bullet does your RCBS mould cast with your alloy? I've used H110 under cast 240 - 255 gr Keith type SWCs and the max load producing SAAMI MAPs is 23 - 25 gr. That's based on my own pressure testing with an Oehler M43 in a Contender...
    8 replies | 132 view(s)
  • ShooterAZ's Avatar
    Yesterday, 09:11 PM
    I size my 44 mags to .430-.431 depending on which boolit. For hunting I would use 18.5-19.5 gr of 2400. For all around use I use 8.5 gr of Unique.
    4 replies | 78 view(s)
  • ShooterAZ's Avatar
    Yesterday, 09:00 PM
    Drop back 1 grain if you are concerned. The Lyman data should be fine though. I have been using 19.5 gr of 2400 for years (decades) with that boolit for hunting, I got better accuracy with 2400 than any of the H110 loads I tried. 18.5 gives even...
    8 replies | 132 view(s)
  • Larry Gibson's Avatar
    Yesterday, 07:53 PM
    Yes, please define your concept of consistent?
    5 replies | 194 view(s)
  • Larry Gibson's Avatar
    Yesterday, 04:33 PM
    My older (60s) RCBS 45 ACP seater will not roll crimp 45 AR cases.
    13 replies | 394 view(s)
  • Larry Gibson's Avatar
    Yesterday, 03:10 PM
    12" twist?
    5 replies | 59 view(s)
  • Larry Gibson's Avatar
    09-23-2017, 06:16 PM
    Larry Gibson replied to a thread Bullet trouble in Cast Boolits
    Noe 316299 You might want to slug aor chamber cast the chamber neck to make sure a .316 bullet seated in the case will chamber.
    4 replies | 220 view(s)
  • Larry Gibson's Avatar
    09-23-2017, 01:02 PM
    The alloy and lube you're using for your BP loads will work just fine with smokeless powder if velocities remain the same.
    4 replies | 103 view(s)
  • ShooterAZ's Avatar
    09-21-2017, 08:24 PM
    I've heard of it but have never tried it. It does look promising. I'm going to be going to Sportsman's Warehouse tomorrow for some other stuff, I may have to see if they have any and try it in my Lyman 54 Deerstalker.
    12 replies | 354 view(s)
  • Larry Gibson's Avatar
    09-21-2017, 07:09 PM
    No, 26-27 gr H4895 will be right at 100% load density. Velocity will be 1800-1900 fps.
    7 replies | 274 view(s)
  • Larry Gibson's Avatar
    09-21-2017, 11:07 AM
    Lee's C312-155 sized at .312 shoot very well with no leading in my Russian SKS. It had a groove diameter of .311. I have shot other cast bullets sized .311 w/o any problems. I use GC'd (Hornady's) bullets and a good NRA 50/50 lube such as Lars...
    7 replies | 274 view(s)
  • Larry Gibson's Avatar
    09-21-2017, 10:54 AM
    Magnum rifle primers were also developed for (other than the large capacity magnums) the use of medium and slower burning ball powders in standard cases, especially for use in colder climates. The CCI 250s work very well in cases from 30-30 up...
    19 replies | 438 view(s)
  • Larry Gibson's Avatar
    09-20-2017, 09:25 PM
    I talked with Al this morning. We reminisced about SSG Pierce and the events 52 years ago today. I also told him I was still holding a grudge he ripped open my pant leg as the rip was from the crotch to below the knee.......thank goodness for...
    21 replies | 694 view(s)
  • Larry Gibson's Avatar
    09-20-2017, 05:25 PM
    On 20 September, 1965 SSG Larry Pierce sacrificed his life to save myself and other of his fellow soldiers near Ben Cat, Republic of South Viet Nam. He was awarded the MOH posthumously. Also wounded in action that day was Alfred Rascon who would...
    21 replies | 694 view(s)
  • Larry Gibson's Avatar
    09-20-2017, 05:20 PM
    Concur with cpaspr ^^^^^^
    75 replies | 2392 view(s)
More Activity
About ShooterAZ

Basic Information

About ShooterAZ
Location:
Northern Arizona
Occupation:
Not affiliated with AZ Game & Fish

Statistics


Total Posts
Total Posts
2,155
Posts Per Day
1.03
General Information
Last Activity
Yesterday 10:12 PM
Join Date
01-09-2012
Referrals
1

2 Friends

  1. Larry Gibson Larry Gibson is offline

    Boolit Master

    Larry Gibson
  2. Lizard333 Lizard333 is offline

    Boolit Master

    Lizard333
Showing Friends 1 to 2 of 2
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check