Inline FabricationRepackboxWidenersGraf & Sons
Lee PrecisionMidSouth Shooters SupplyRotoMetals2Titan Reloading

Tab Content
  • bosterr's Avatar
    04-16-2019, 05:55 PM
    If you're using pure lead in an aluminum mold you're way too cold. You need to be at 800 degrees or hotter.
    5 replies | 118 view(s)
  • bosterr's Avatar
    04-15-2019, 06:28 PM
    But we're talking Accurate Molds here. The cavities will be identical.
    12 replies | 209 view(s)
  • bosterr's Avatar
    04-09-2019, 05:54 PM
    bosterr replied to a thread Danger in Our Town
    Believe it or not, no problem! I didn't get a chance to look through it. He just said there's a little lead in the bore. He ran a brush through it and handed it to me and it looked fine.
    20 replies | 775 view(s)
  • bosterr's Avatar
    04-09-2019, 03:20 PM
    bosterr replied to a thread Danger in Our Town
    How about a buddy firing a 44 mag lead boolit in my 14 inch 309 JDJ Contender?
    20 replies | 775 view(s)
  • bosterr's Avatar
    04-07-2019, 08:35 AM
    I just happen to have a Canjar trigger that a friend sold me way back to put in a Rem. 541T that has long since gone down the road. I can't remember if I couldn't get it to work or if I couldn't get it as light as I wanted, so it sits on the shelf....
    20 replies | 718 view(s)
  • bosterr's Avatar
    04-07-2019, 07:58 AM
    This is unexplored territory for me having issues now. I'm pushing 69 years old and don't have a single health problem that's typical with people my age. I'm not bragging, just acknowledging that I'm extremely lucky. Good genes in my family tree I...
    23 replies | 560 view(s)
  • bosterr's Avatar
    04-06-2019, 08:27 AM
    Update: I had my torn retina repaired yesterday by a Retina Specialist. I went to the original doctor back in December to investigate floaters in my left eye. It was then that he found a "slight tear" in the eye. Yesterday the Specialist asked why...
    23 replies | 560 view(s)
  • bosterr's Avatar
    04-04-2019, 08:25 AM
    I have a '94 of 1897 vintage and use the Accurate 32-180C. Since this is a 24" barrel and wanted to make sure there was enough lube on the boolit, I had Tom modify the 32-180A. Since this is a bit longish boolit I trim my Win. 32-40 brass to 2.102...
    4 replies | 182 view(s)
  • bosterr's Avatar
    04-03-2019, 01:12 PM
    I went to an opthamologist last December with a "floater" issue and the doctor said I had a slight retina tear as well. I went again to see the doctor yesterday and he said the tear should be fixed very soon as well as the thinning of the edge right...
    23 replies | 560 view(s)
  • bosterr's Avatar
    04-01-2019, 08:14 AM
    Tom's site says he dosen't give you the tracking number. He dosen't like poking them into the computer any more than I do. He always beats his 3 week turn around time and that's good enough for me.
    8 replies | 319 view(s)
  • bosterr's Avatar
    03-26-2019, 07:53 AM
    bosterr replied to a thread Trophy? in Hunting with CB's
    Back straps taste better than antlers anyway!
    10 replies | 623 view(s)
No More Results
About bosterr

Basic Information

Age
68
About bosterr
Location:
Western Pa.
Interests:
Hunting, Shooting
Occupation:
Equipment Operator

Statistics


Total Posts
Total Posts
553
Posts Per Day
0.21
General Information
Join Date
12-27-2011
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check