Graf & SonsStainLess Steel MediaInline FabricationRotoMetals2
ADvertise hereLee PrecisionTitan Reloading

Tab Content
  • aarolar's Avatar
    10-21-2017, 01:32 PM
    aarolar replied to a thread Procedure question in Muzzleloading.
    Fraid I just missed gun is dead on still... Sent from my SM-G900V using Tapatalk
    26 replies | 691 view(s)
  • aarolar's Avatar
    10-21-2017, 12:19 PM
    aarolar replied to a thread Procedure question in Muzzleloading.
    Well the gun went boom but I missed 3 absolutely gimme shots on squrriel gonna check my sights when I get home something seems off. Sent from my SM-G900V using Tapatalk
    26 replies | 691 view(s)
  • aarolar's Avatar
    10-20-2017, 09:39 PM
    aarolar replied to a thread Procedure question in Muzzleloading.
    Too late now I'm leaving it until after tomorrow's hunt. I did swab it with a dry patch both sides then run a patch lightly coated in my lube down it. Sent from my SM-G900V using Tapatalk
    26 replies | 691 view(s)
  • aarolar's Avatar
    10-20-2017, 09:05 PM
    I was careful to remove all the solder joints and use just the pipe. Sent from my SM-G900V using Tapatalk
    5 replies | 243 view(s)
  • aarolar's Avatar
    10-20-2017, 08:40 PM
    aarolar replied to a thread Procedure question in Muzzleloading.
    Using my own rendered pig lard, should I swab with that or something else alls else I have is bore butter which I've purty near swarn off. Sent from my SM-G900V using Tapatalk
    26 replies | 691 view(s)
  • aarolar's Avatar
    10-20-2017, 07:57 PM
    I just sorta confirmed my suspicion, tested a piece of pipe without heating it at all and it tested .040. Can I anneal it back and if so what temp should I use? Sent from my SM-G900V using Tapatalk
    5 replies | 243 view(s)
  • aarolar's Avatar
    10-20-2017, 07:54 PM
    aarolar replied to a thread Procedure question in Muzzleloading.
    Goex Sent from my SM-G900V using Tapatalk
    26 replies | 691 view(s)
  • aarolar's Avatar
    10-20-2017, 07:34 PM
    Will pure cast lead ever be as soft as swaged? I have a homemade cabine tree style tester and swaged hornady round balls test at .035-.040 my pure cast lead balls test more around .060, I have tried both lead pipe and lead sheet and tje results are...
    5 replies | 243 view(s)
  • aarolar's Avatar
    10-20-2017, 07:27 PM
    I discharged my hawken this afternoon, took out a nasty coyote, reloaded and finished my hunt. Didn't see any deer I'm planning on going again in the morning, should I pull the load and clean the gun or should I just leave it loaded and hunt...
    26 replies | 691 view(s)
No More Results
About aarolar

Basic Information

About aarolar
Location:
Augusta GA

Statistics


Total Posts
Total Posts
371
Posts Per Day
0.17
General Information
Last Activity
Today 03:28 PM
Join Date
12-18-2011
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check