Lee PrecisionMidSouth Shooters SupplyTitan ReloadingRotoMetals2
Graf & SonsADvertise hereStainLess Steel MediaInline Fabrication

Tab Content
  • Wolfer's Avatar
    Yesterday, 07:10 PM
    Yes it is
    10 replies | 243 view(s)
  • Wolfer's Avatar
    06-18-2018, 05:42 PM
    Ive used hedge apple for several pistol grips. It is extremely hard and durable. However the yellow color always turns brown in a couple years. Under the grips where it never sees sunlight it stays yellow. Ive only used oil type finishes on it. I...
    10 replies | 243 view(s)
  • Wolfer's Avatar
    06-18-2018, 05:32 PM
    Even though hard on powder it would still be a lot of fun. The concealable version could shoot hedge apples.
    26 replies | 10521 view(s)
  • Wolfer's Avatar
    06-15-2018, 10:21 PM
    I use the 311008 as cast at .312 with one coat of LLA and 5 gr of clays. Ive not tried them in 30-06 but shot lots in 30-30 and 30-40 They run 1200/1100 respectively and hit close enough to poa when lined up for deer loads. It may not be legal to...
    16 replies | 386 view(s)
  • Wolfer's Avatar
    06-10-2018, 06:31 PM
    Wolfer replied to a thread Rocky Raab? in Cast Boolits
    I use the 311008 with 5 gr of clays. 1100/1200 fps from 30-30 and 30-40, very accurate and lots of fun
    21 replies | 3536 view(s)
  • Wolfer's Avatar
    06-10-2018, 11:49 AM
    Wolfer replied to a thread 14" twist in 45-70?? in Cast Boolits
    Upon further study it appears the 14" twist should be ok for my purposes. Running the lee 340 or 405 or maybe the Gould boolit to 1200 fps or thereabouts with smokeless in a 67/89 rolling block. I'm quite confident I can take a deer with these...
    5 replies | 261 view(s)
  • Wolfer's Avatar
    06-06-2018, 07:45 PM
    Green mtn has some .458 barrels with 14" twist that are not too bad priced. I'm wanting to build 4 Swedish rolling blocks into 45-70. I won't be shooting anything heavier than 405 gr and at trapdoor speeds. Is this too fast a twist? I would prefer...
    5 replies | 261 view(s)
  • Wolfer's Avatar
    06-04-2018, 07:41 PM
    The reason I need another tractor and the reason I don't put a spark arrester is because my tractor isn't big enough. My round baler requires a 40 hp min on the pto. My Massey put out slightly more than 40 hp when it was new in 58. I have a fixed...
    21 replies | 848 view(s)
  • Wolfer's Avatar
    06-03-2018, 02:51 PM
    A 3" shell will chamber in a 2-3/4" chamber. There's just nowhere for the crimp to go when you fire it.
    14 replies | 395 view(s)
  • Wolfer's Avatar
    06-03-2018, 02:45 PM
    A little salt helps a not so good meal for me also.
    21 replies | 848 view(s)
  • Wolfer's Avatar
    06-02-2018, 08:07 PM
    I don't have a barn to put them in but if I did they would set out a few days first. This one had been dumped 45 min or more before I seen it start smoking. Last year I saw a spark go in the baler which started smoking but I got it dumped. Hay was...
    21 replies | 848 view(s)
  • Wolfer's Avatar
    06-02-2018, 07:29 PM
    My old Massey Ferguson 65 model of 1958 is notorious for throwing sparks. Most of them were. Ive got to get another tractor.
    21 replies | 848 view(s)
  • Wolfer's Avatar
    05-28-2018, 04:29 PM
    I have an old lathe and love to tinker so I built me some dies to use the belted magnum cases. Once fireformed I just neck size. My thoughts was I could buy a barrel blank cheaper than dies. Green mtn has a 27" .458 blank for $110 or thereabouts....
    11 replies | 386 view(s)
  • Wolfer's Avatar
    05-25-2018, 10:11 PM
    Like 17 nut I use belted magnum cases. I have a lathe but it's a 4 jaw chuck so I put them in my drill press and use a file to remove the belt. My cases have been fired several times and are too big at the back. I made a die that I drive them into...
    12 replies | 489 view(s)
  • Wolfer's Avatar
    05-23-2018, 07:01 PM
    I made a block that I soldered to the barrel up against the tulip. Drilled/tapped it for an H&R muzzleloader base turned backwards. I also filed a dovetail in it for peep type sight I got from brownells. I plan on replacing the front sight with a...
    15 replies | 1391 view(s)
No More Results
About Wolfer

Basic Information

About Wolfer
Biography:
Avid hunter,shooter,
Location:
Southwest MO.
Interests:
Hunting,shooting,bullet casting
Occupation:
Electrician

Signature


Some people live and learn but I mostly just live

Statistics


Total Posts
Total Posts
1,643
Posts Per Day
0.69
Albums
Total Albums
1
Total Photos
0
General Information
Last Activity
Yesterday 07:11 PM
Join Date
12-04-2011
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check