Titan ReloadingADvertise hereRotoMetals2Graf & Sons
StainLess Steel MediaMidSouth Shooters SupplyLee PrecisionInline Fabrication

Tab Content
  • Forrest r's Avatar
    Yesterday, 04:02 PM
    I've been running that same bullet with a oal of 1.180" in 2 different 1911's.
    7 replies | 111 view(s)
  • Forrest r's Avatar
    06-16-2018, 09:02 AM
    Forrest r replied to a thread M A S model 45 in Rimfire Area
    They actually thinned the bbl down on the mas 45 compared to the then "target" rifles of the day. A mas 45 next to a mauser es340b made in 1934. The mas front sights are square & the mauser target rifle sights are chisel pointed to match the 6...
    13 replies | 365 view(s)
  • Forrest r's Avatar
    06-12-2018, 02:42 AM
    Forrest r replied to a thread M A S model 45 in Rimfire Area
    These are great full size rifles that bring a lot to the table for little $$$. Still have 1 laying around un-issued in cosmoline. If you look at the side of the front sight on the mas you will see a # stamped it it. It will be a...
    13 replies | 365 view(s)
  • Forrest r's Avatar
    06-10-2018, 04:12 PM
    2400 is a good all around plinking powder. Playing around with pc'd bullets in a 308w using the lee 312-160 tl bullet. A 100yd 10-shot group that measures 1 3/8" outside edge to outside edge. The 16.0gr of 2400/egan 308 bullet pc'd needs a...
    281 replies | 103455 view(s)
  • Forrest r's Avatar
    06-10-2018, 07:26 AM
    For me the pc'd bullets have always been faster. Same bullet cast from the same alloy/same time. PC VS Traditional lube ='s pc is faster with fast burning pistol powders and rifle powders
    10 replies | 376 view(s)
  • Forrest r's Avatar
    06-05-2018, 07:12 AM
    A simple formula that will show you how much up/down you need for your sight height: distance between the sights X (amount off target \ inches to target) Example: I have a revolver that is shooting 6" high @ 25yds. distance between sights...
    32 replies | 3020 view(s)
  • Forrest r's Avatar
    06-05-2018, 06:49 AM
    While cylinder gap plays a role in the velocity, the cylinder hole size itself and the bbl are the main players. Bought a nib 586 back in 1987. Put 100,000 rounds thru it and sent it back to s&w to have the timing rebuilt/bbl set back/new forcing...
    12 replies | 349 view(s)
  • Forrest r's Avatar
    06-05-2018, 05:54 AM
    I've been using 45/45/10 on my pc'd rifle bullets lately. Doesn't harm anything and the tl lubed/pc'd bullets season the bbl so I can switch to traditional cast/lubed bullets and test the same loads in the next string. The last outing with pc +...
    3 replies | 183 view(s)
  • Forrest r's Avatar
    06-04-2018, 04:37 AM
    I'm sure there is a difference in accuracy between the hp designs of the 358640's. I personally haven't seen any but I'm only using that bullet for short range plinking (25yd and closer). On the to do list is testing the 503's @ 100yds to see if...
    8 replies | 331 view(s)
  • Forrest r's Avatar
    06-02-2018, 06:25 AM
    It's extremely common for reloaders to read/use "generic data" and apply it to specific bullets. Alliant uses 3.6gr of bullseye for "their" 158gr lswc data Alliant also uses 2.8gr of bullsyeye for "their" lwc data Lyman 311156 ='s 4.0gr...
    12 replies | 419 view(s)
  • Forrest r's Avatar
    06-02-2018, 04:42 AM
    Not hand/cherry picked targets by any means. Nothing more than the test targets used to test loads for a then new 686. Was looking for a plinking load. 6-shot groups @ 50ft. 3.3gr of bullseye 3.5gr of international clays mixed 38spl cases/federal...
    8 replies | 331 view(s)
  • Forrest r's Avatar
    05-23-2018, 05:40 AM
    Hard to beat clays for plinking loads in the 44mag. 6.0gr to 6.5gr of clays and bullets in the 200gr to 250gr range do extremely well. Mihec 245gr hp's & 6.0gr of clays h&g #142 gc'd 220gr swc/200gr hpswc doesn't matter both bullets combined...
    33 replies | 1282 view(s)
  • Forrest r's Avatar
    05-22-2018, 05:40 AM
    The only thing I do is water quench the bullets when they are 1st cast. I so this simply because I don't want the bullets hitting each other and distorting each other. I don't do anything to pc'd bullets other then let them air cool.
    11 replies | 738 view(s)
  • Forrest r's Avatar
    05-21-2018, 06:57 AM
    My 4" bbl'd 29-3 has seen a couple rounds down the tube, actually a couple rounds too many. Too bad about your 29-3, they are an excellent workhorse proving shooters with countless hours of quality range time.
    11 replies | 578 view(s)
  • Forrest r's Avatar
    05-21-2018, 06:40 AM
    2700 with 2 moa acuracy for 10-shot groups @ 100yds. Alloy was 4 parts range scrap 1 part mono-type. 1 coat of shake & bake pc/john deere green from smoke. Used bore-tech eliminator to get the black streaks out of the bbl. No leading
    11 replies | 738 view(s)
  • Forrest r's Avatar
    05-19-2018, 08:04 AM
    lyman lists the alliant reloading powders as Rx!! And accurate powders as AA-!!!! for rifle powders and AA#! for pistol powders
    2 replies | 184 view(s)
No More Results
About Forrest r

Basic Information

About Forrest r
NE Ohio


Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
Yesterday 04:03 PM
Join Date

1 Friend

  1. novalty novalty is offline

    Boolit Master

Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check