Lee PrecisionGraf & SonsStainLess Steel MediaInline Fabrication
MidSouth Shooters SupplyRotoMetals2Titan ReloadingADvertise here

  • DonMountain's Avatar
    Yesterday, 01:10 PM
    This looks like an interesting proposal. I could unscrew the handle on my old Pacific C press and fabricate a shaft to screw back into its place, with a right angle bolt welded to it with the bolt head projecting so I can just put a click...
    33 replies | 631 view(s)
  • DonMountain's Avatar
    06-18-2018, 03:27 PM
    I have been seating primers on my Hornady 007 press with automatic primer feed for at least 30 years now too, with never a misfire. But all my brass was good old American made from Winchester, Remington and Federal. These oddball 9mm Luger and 380...
    33 replies | 631 view(s)
  • DonMountain's Avatar
    06-16-2018, 10:21 PM
    But I can tell immediately when I pull the trigger if I have attained "consistent performance" from one of my 9mm Luger pistols. It either fires or it doesn't. When I started loading for these by setting my primers by "feel", I had a 30% non-fire...
    33 replies | 631 view(s)
  • DonMountain's Avatar
    06-16-2018, 02:45 PM
    There, this is what I want! Thank you for stating this Dan Cash! My antique 9mm Luger pistols seem to have a high percentage of misfires unless the primers are set to the exact same depth in the cartridge cases. So, we all know if I am using...
    33 replies | 631 view(s)
  • DonMountain's Avatar
    06-16-2018, 02:24 PM
    I looked at this tool on the RCBS website, there was no explanation on how the primer insertion depth is adjusted. The RCBS RAM-PRIME that I use is easy to adjust by screwing the device up or down and setting the locknut like you do with a typical...
    33 replies | 631 view(s)
  • DonMountain's Avatar
    06-15-2018, 07:27 PM
    I looked at both of these priming tools, the one from 21st Century and the Sinclair tool, and it seems like my RCBS Ram Prime tool is a better solution for far less money. But again, I have to hand load individual primers which I was trying to get...
    33 replies | 631 view(s)
  • DonMountain's Avatar
    06-15-2018, 04:23 PM
    Over the years I have been using various methods of inserting primers into cases. Mostly Hornady and Pacific presses, which do not set primers to a precise depth, but only give you a "feeling of pressure" when you hit the bottom of the primer...
    33 replies | 631 view(s)
  • DonMountain's Avatar
    06-13-2018, 02:13 PM
    My wife does real well fixing the ground hogs for supper, and we are now getting a lot of those armadillo around here to. Can you give us your recipe for fixing armadillo?
    25 replies | 548 view(s)
  • DonMountain's Avatar
    06-05-2018, 02:39 PM
    I have a CZ-52 in 7.62x25 that I recently purchased some Starline brass for to start reloading. And looking through my bullet molds, the only one I have in that approximate size is the Lyman 311359, which is a pointed nose mold. Has anybody tried...
    3 replies | 184 view(s)
  • DonMountain's Avatar
    06-02-2018, 12:29 PM
    I think both of these presses are really cheap and not worth much money so would keep both of them set up for different operations. But maybe you are not as lazy as I am and enjoy swapping dies and such?
    19 replies | 547 view(s)
No More Results
About DonMountain

Basic Information

About DonMountain
Biography:
NRA Life Member
Location:
Mid-Missouri
Interests:
Antique Military Rifles

Statistics


Total Posts
Total Posts
768
Posts Per Day
0.32
General Information
Last Activity
Today 02:57 PM
Join Date
11-22-2011
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check