Lee PrecisionMidSouth Shooters SupplyTitan ReloadingInline Fabrication
ADvertise hereRotoMetals2StainLess Steel MediaGraf & Sons

Tab Content
  • LenH's Avatar
    02-21-2018, 09:21 AM
    I got an oil pan heater for about $13 from Amazon, that and a lamp dimmer switch from Home Depot and was set.
    14 replies | 551 view(s)
  • LenH's Avatar
    02-20-2018, 02:52 PM
    My wag came from your estimate of how much you posted of your estimated weight and divided by 2, I missed it by a bit over 100. The lady that delivers our mail doesn't like it when I order lead from some one. She usually has the box in one of...
    256 replies | 5092 view(s)
  • LenH's Avatar
    02-20-2018, 09:46 AM
    Be careful heating ingots, I had a mess on my hands one day when the heat was up too high. I had a big ole mess on my reloading bench. I place ingots around the rim of the pot now.
    14 replies | 312 view(s)
  • LenH's Avatar
    02-16-2018, 11:58 AM
    I have that mold in a 6 cavity, shoots great out of a .38 revolver.
    5 replies | 461 view(s)
  • LenH's Avatar
    02-15-2018, 11:07 AM
    LenH replied to a thread Tac 1 lube? in Boolit Lube !
    Several years ago Randy sold a kit to make Tac-1. The kit made 1# of lube and it was pale green and a bit hard to see in small lube groves. I talked to Randy several times about this and he started adding a dye to the lube to make it darker. I...
    13 replies | 428 view(s)
  • LenH's Avatar
    02-13-2018, 09:51 AM
    Impressive, I am still trying to figure out a bullet at 100 yards. But I have only been trying cast about a year.
    77 replies | 2069 view(s)
  • LenH's Avatar
    02-12-2018, 05:24 PM
    I am going with 2850.
    256 replies | 5092 view(s)
  • LenH's Avatar
    02-09-2018, 05:12 PM
    John, it is not a typo. I am slow an methodical. I am not out to run a race and have done more than that in an hour. I am the same way when I reload, I have a 550B and if I get 250+ an hour, that is just fine with me.
    16 replies | 690 view(s)
  • LenH's Avatar
    02-07-2018, 10:06 AM
    I bought a used Promelt from a guy on the Swappin & selling page, it was shipped with digital controller similar to yours. The TC was hard wired to the PID and the wire was anchored to the inside of the box. I cut the wire and added a female plug...
    15 replies | 630 view(s)
  • LenH's Avatar
    02-02-2018, 04:28 PM
    I was invited to go with a buddy & his dad to shoot. We got to where the `gun range' which was a sand pit. He handed me a Ruger Blackhawk .45 Colt and a box of his hand loads, `SAVE MY BRASS, BOY' was all he said besides be careful after his gun...
    91 replies | 2102 view(s)
  • LenH's Avatar
    02-01-2018, 09:39 AM
    I think fit is more important than BNH. I have been shooting #2 mixed with pure almost 50/50, but in .45 AP.
    10 replies | 314 view(s)
No More Results
About LenH

Basic Information

About LenH
Location:
East Arkansas
Interests:
Casting, Reloading, Shooting,Cooking, sausage making and being a general irritation to my family.
Occupation:
Structural Steel Detailer

Statistics


Total Posts
Total Posts
292
Posts Per Day
0.13
General Information
Last Activity
Yesterday 09:50 PM
Join Date
11-10-2011
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check