Lee PrecisionTitan ReloadingMidSouth Shooters SupplyRotoMetals2
Inline FabricationWidenersRepackboxADvertise here

Tab Content
  • LenH's Avatar
    03-27-2020, 02:53 PM
    A friend's dad was a mechanic for a long ago gone truck line. He would bring me big coffee cans full of these things that kept both of us shooting for a while. That was way back in the 70's. I just wish I had known at the time about mixing 50/50...
    15 replies | 891 view(s)
  • LenH's Avatar
    03-26-2020, 08:46 AM
    Don't think you are the only one to do that. I did it with .45 colt and .357 cases and no I didn't do it again.
    37 replies | 1323 view(s)
  • LenH's Avatar
    03-26-2020, 08:44 AM
    LenH replied to a thread 550 happiness? in Reloading Equipment
    I found one used from a guy that was getting out of the game, I almost felt bad at the time but the guy's wife wanted it gone. I got his whole reloading room for $350. That was in 2004 and have loaded tones of bullets on the thing. I don't think...
    30 replies | 754 view(s)
  • LenH's Avatar
    03-26-2020, 08:35 AM
    I use a homemade lead hammer with an all thread handle wrapped in electrical tape. There is a sticky here somewhere that shows how to do it. When is gets beat up just stick it in the melt and then cast a new one. I use some 6 & 8 cavity molds,...
    27 replies | 579 view(s)
  • LenH's Avatar
    03-26-2020, 08:21 AM
    I never really gave it much thought but some bullets have deeper groves than others. Don't sweat the small stuff, I live by the general rule of 'FIT IS KING all else is secondary.' That has served me well over the years.
    15 replies | 522 view(s)
  • LenH's Avatar
    03-24-2020, 12:01 PM
    LenH replied to a thread Preheating mold in Cast Boolits
    I use the solid top hot plate and set it to right at a little less than medium when I get the melt started and they are ready at the same time. I have an 8 cavity H&G and have gotten it too hot twice. That beast takes a while to cool down. When I...
    40 replies | 889 view(s)
  • LenH's Avatar
    03-19-2020, 09:00 AM
    I have one of the primer catchers in the link. It is hooked up to an old spartan press. It works pretty good but it will miss one every now and then. I have a piece of clear plastic tubing and use a plastic nut container from Sam's Club to catch...
    8 replies | 424 view(s)
  • LenH's Avatar
    03-05-2020, 09:43 AM
    Never really give it much thought, but it is never enough.
    64 replies | 2757 view(s)
  • LenH's Avatar
    03-05-2020, 09:30 AM
    LenH replied to a thread Lubesizer heaters in Boolit Lube !
    I found a small oil pan heater on Amazon about 4 years ago for about 10 bucks, I got it in the summer months and it was cheaper. it is 25 watts and 1" X 5" and that little thing gets really hot, I use a lamp dimmer switch from a big box store and...
    27 replies | 1576 view(s)
  • LenH's Avatar
    03-04-2020, 02:10 PM
    The only time I have rendered indoor range lead, it was free. I had to wait until the range closed and the owner took me in the back door where there were piles of the scrap. I was able to get a half of a 5 gallon bucket. That is what I could carry...
    46 replies | 2568 view(s)
No More Results
About LenH

Basic Information

About LenH
Location:
East Arkansas
Interests:
Casting, Reloading, Shooting,Cooking, sausage making and being a general irritation to my family.
Occupation:
Structural Steel Detailer

Statistics


Total Posts
Total Posts
468
Posts Per Day
0.15
General Information
Last Activity
Today 04:49 PM
Join Date
11-10-2011
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check