Inline FabricationRotoMetals2WidenersADvertise here
Titan ReloadingLee PrecisionRepackboxMidSouth Shooters Supply

Tab Content
  • Shuz's Avatar
    03-29-2020, 04:06 PM
    Smoke--Im sending a PayPal transaction for 1 lb of the black and 1 lb of the traffic purple. This is my first trial in powder coating and I'd appreciate any tips on how to do this. Thank's Shuz
    35 replies | 1256 view(s)
  • Shuz's Avatar
    03-28-2020, 01:52 PM
    Hardcast--Thanks for the info regarding the 423 origin. Yesterday I cast a couple of hundred round point 432-423 boolits from my brand new 4C brass MP mold. I was amazed that the delta was only. 9g amongst the 4 cavities!! The average weight was...
    52 replies | 1028 view(s)
  • Shuz's Avatar
    03-27-2020, 02:11 PM
    Hardcast-- I'm not familiar with the Lyman mould you referred to, but if you've looked at the MP-432-423, you'll notice that there is a small front driving band in the SWC style and that feature makes it cut nice clean holes in paper targets. The...
    52 replies | 1028 view(s)
  • Shuz's Avatar
    03-27-2020, 10:57 AM
    I have had a Mdl 69 in 4-1/4" bbl for several years now. Mine wears Hogue X frame grips. I installed a Patridge front sight and a Wolff rebound slide spring.This revolver is now one of my, if not "the", favorite .44 magnum Smith. A great load with...
    52 replies | 1028 view(s)
  • Shuz's Avatar
    03-24-2020, 12:53 PM
    Dan, what is the mould number of your MP 30 cal mould? Is it a gas check design? If so,,what is the gas check shank diameter?
    3 replies | 492 view(s)
  • Shuz's Avatar
    03-15-2020, 04:27 PM
    Shuz replied to a thread WTB; MP Molds part in Swappin & Sellin
    contender1-- Are you willing to honco a group buy on MP mold parts?
    5 replies | 317 view(s)
  • Shuz's Avatar
    03-14-2020, 01:35 PM
    I have a new, never been used set of small Lyman handles that I'll sell for $20.00 shipped CONUS.
    4 replies | 259 view(s)
  • Shuz's Avatar
    03-14-2020, 01:30 PM
    Shuz replied to a thread WTB; MP Molds part in Swappin & Sellin
    A couple days ago I broke 2 of the sliding pins that fit into the hollow point pin of a round pin for my MP 432-423. I suppose Miha sells spares for these as well? Perhaps we could go together and get what we both need? These parts could fit into a...
    5 replies | 317 view(s)
  • Shuz's Avatar
    03-10-2020, 02:31 PM
    Folks, just the other day I was going thru some old invoices on gun related stuff, and came across an old invoice formDillon from 1983 when I bought a new 450set up for 7mm TCU for $199.99!! I didn't find one for my Square Deal B but if I recall,...
    15 replies | 687 view(s)
  • Shuz's Avatar
    03-10-2020, 10:56 AM
    Shuz replied to a thread Welterweight 44s in Cast Boolits
    I have the MP-432-423 mould in a 2C, and wish I had a 4C! This design shoots very well outta my 5" 629-3 Classic DX with a 4x Leupold EER scope. Last Friday I shot groups that measured between 1.3 and 2.2" @ 25 yards. Velocity was 1223fps with SD of...
    24 replies | 1244 view(s)
  • Shuz's Avatar
    03-09-2020, 10:19 AM
    Living out in the sticks where I can't see my neighbors sure has it's advantages. You don't say where you live. I suggest that you might find some guy near you who would be glad to help you, I know I would!:drinks:
    108 replies | 4980 view(s)
  • Shuz's Avatar
    03-08-2020, 08:46 PM
    Nice piece! Is it a dash 5?
    20 replies | 1020 view(s)
  • Shuz's Avatar
    03-05-2020, 11:35 AM
    Shuz replied to a thread Welterweight 44s in Cast Boolits
    MP Molds makes a 225g plain base design that I use designated: MP-433-640L. It is a lighter version of MP's clone of the Lyman Devastator 429640. This design, backed by 8.9g of Green Dot(what else?:drinks:) has given me several 5 shot groups at 25...
    24 replies | 1244 view(s)
  • Shuz's Avatar
    03-03-2020, 11:47 AM
    8.0g of Titegroup gives me 1009fps with an SD of 12 with a H&G 503 MP clone at OAL of 1.690". 5 shot group was 1.272" at 25 yards with a 4x Leupold EER scope mounted on a Smith 629 Classic DX 5" bbl. This was from a sandbag rest. This same load shot...
    25 replies | 928 view(s)
No More Results
About Shuz

Basic Information

About Shuz
Location:
Nine Mile Falls,Wa.
Interests:
casting,reloading, shooting,hunting
Occupation:
Retired

Signature


It's all chicken, even the beak!

Statistics


Total Posts
Total Posts
2,291
Posts Per Day
0.42
General Information
Last Activity
Today 10:41 AM
Join Date
03-24-2005
Referrals
0

2 Friends

  1. Cosmiceyes Cosmiceyes is offline

    Boolit Buddy

    Cosmiceyes
  2. jabo52521 jabo52521 is offline

    Boolit Buddy

    jabo52521
Showing Friends 1 to 2 of 2
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check