RotoMetals2Lee PrecisionStainLess Steel MediaADvertise here
MidSouth Shooters SupplyGraf & SonsInline FabricationTitan Reloading

Tab Content
  • SharuLady's Avatar
    04-18-2018, 02:22 PM
    Hi HATCH, Is it safe to assume that the parts you were waiting on for the PID I wanted has come in? SharuLady
    63 replies | 9073 view(s)
  • SharuLady's Avatar
    04-12-2018, 12:17 PM
    Hi, As I stated in the OP: I was kindly given these 20 boolits from a gentleman that lives nearby me. He no longer has the rifle that he was loading for (30-30). I should have asked him if he still had the mold & if he was interested in...
    6 replies | 219 view(s)
  • SharuLady's Avatar
    04-12-2018, 09:30 AM
    OK, 200* C equates to approx. 392F. So, baking the PCing for the 10 to 20 min would not cause a problem with the GC since it needs to bake the GC for 1 hr.? TY, SharuLady
    6 replies | 219 view(s)
  • SharuLady's Avatar
    04-11-2018, 06:47 PM
    Hi, I have some questions on powdercoating boolits that already have a gas check on them. 1) I know that at times gas checks need to be annealed to be able to mount them, whether by hand or with a sizer. A) what is the temp required to anneal...
    6 replies | 219 view(s)
  • SharuLady's Avatar
    04-10-2018, 01:10 AM
    I would like to have 2 large and 2 small if still available. TY, SharuLady
    19 replies | 454 view(s)
  • SharuLady's Avatar
    04-09-2018, 04:58 PM
    Hi Smoke, The final portion of original order came today, Well packed & arrived safely. Fast shipping! :) Ty, SharuLady
    1 replies | 66 view(s)
  • Bullwolf's Avatar
    04-06-2018, 02:34 AM
    Bullwolf replied to a thread Case Trimming in Cast Boolits
    I use an RCBS case trimmer 2 Mine is mounted to a small oak board, so I can easily clamp it down to a table, or on the loading bench. I'm usually not in a hurry when case trimming, or trimming down cases by a large amount. The addition...
    29 replies | 577 view(s)
  • SharuLady's Avatar
    04-05-2018, 12:26 AM
    Hi, The Lee Alox bottles are 4oz content & on the bottom of the bottle is The diamond shaped emblem which has a #3 in it. Does anyone know if the #3 means it will keep from drying up if I make BLL and put it back into the Lee Alox bottle? Mainly...
    1343 replies | 321617 view(s)
  • Bullwolf's Avatar
    04-01-2018, 10:12 PM
    I'm a right handed, so when I have a Uniflow mounted to the bench, or on a powder stand, or even in the stand off plate on a single stage press, I always left the uniflow set up in the right hand front configuration. Right Hand Front I've...
    20 replies | 777 view(s)
  • Bullwolf's Avatar
    03-31-2018, 02:33 AM
    I use the Bevel Based Lee 358-158-RF boolit in 38/357, but not in 9mm. From Lee Precision 368-158-RF #90303: http://leeprecision.net/support/index.php?/Knowledgebase/Article/View/347/62/cast-bullet-length-dimensions Bullet's Overall Length in...
    43 replies | 1776 view(s)
  • SharuLady's Avatar
    03-28-2018, 05:39 PM
    Hi, just received my copy of Lyman Cast Bullet Handbook Third Edition from Cornell Publishing. Was packaged great and in good condition on arrival. This is a very nice manual!!! Thanks go to BrassMagnet for this great opportunity. SharuLady
    39 replies | 1054 view(s)
  • Bullwolf's Avatar
    03-21-2018, 11:59 PM
    Newer Lee moulds, with a Left Hand threaded sprue plate screw are marked LH on the mould. Like this Dual Cavity Lee (LH) 358-125-RF mould, in the attached image below. Which definitely has a Left Hand threaded sprue plate screw. -...
    41 replies | 1262 view(s)
No More Results
About Bullwolf

Basic Information

Age
49
About Bullwolf
Location:
California/Nevada border

Statistics


Total Posts
Total Posts
1,131
Posts Per Day
0.44
Albums
Total Albums
1
Total Photos
51
General Information
Last Activity
Yesterday 02:42 AM
Join Date
04-25-2011
Referrals
0

1 Friend

  1. SharuLady SharuLady is offline

    Boolit Man

    SharuLady
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check