Wisconsin TriggerRotoMetals2Lee PrecisionTitan Reloading
Inline FabricationStainLess Steel MediaGraf & SonsMidSouth Shooters Supply

Tab Content
  • Bullwolf's Avatar
    07-09-2017, 08:24 PM
    Night time casting a few 38 caliber full wad cutters on the picnic table. Using my hand held electric ladle (a Hilts Molds Hot 1) and two WC moulds. - Bullwolf
    15 replies | 2109 view(s)
  • Bullwolf's Avatar
    07-07-2017, 11:13 PM
    Bullwolf replied to a thread Tumble Lube tedium? in Cast Boolits
    I've done it either way, but usually I'll take the time to stand em up while I'm waiting for them to dry. But I'm a little bit OCD when it comes to loading, and my boolits. Typically while I'm tumble lubing that's my current focus, and not...
    26 replies | 1120 view(s)
  • Bullwolf's Avatar
    07-07-2017, 08:41 PM
    I use a finger swipe of Bag Balm whenever I have to size down cast boolits by a good amount. www.bagbalm.com It has a Petrolatum Lanolin base. (read that as Lanolin, and Vaseline Petroleum Jelly basically) I think of it as pre-mixed...
    19 replies | 673 view(s)
  • Bullwolf's Avatar
    07-07-2017, 08:19 PM
    Saw this post a while back and decided I should try out the rhubarb-bread myself. What an interesting idea. Boy was it tart and delicious! Much thanks to Lloyd Smale and MaryB for mentioning it on the forum. - Bullwolf
    15 replies | 659 view(s)
  • Bullwolf's Avatar
    07-07-2017, 12:22 AM
    This may seem silly, but I dislike all the sugar that's found in most store bought beef jerky, or other jerky recipes. I don't really enjoy eating sweetened jerky. So here is my no sugar jerky recipe: 3 lbs of lean beef or venison. Trimmed...
    2 replies | 210 view(s)
  • Bullwolf's Avatar
    07-06-2017, 11:54 PM
    I garden, and I grow a lot of different things to eat. Also can some stuff as well, and freeze other things like fruits and berries to later make jam and jellies from. I've had poor luck canning and freezing potatoes however. I recently...
    2 replies | 207 view(s)
  • Bullwolf's Avatar
    07-04-2017, 09:37 PM
    Yes my mould has a ding in the same location, and only on one side. No idea what it was for, or why it's there. I purchased my mould many years ago, at a gun show. Never noticed the ding until you mentioned it. It does not appear to...
    13 replies | 569 view(s)
  • Bullwolf's Avatar
    07-01-2017, 12:43 AM
    The Bullseye powder inside my yellow can does not have any holes or perforations in the center of the powder flakes. Looks the same as modern Alliant Bullseye powder to me.
    12 replies | 1065 view(s)
  • Bullwolf's Avatar
    06-29-2017, 10:58 PM
    I have the same Lee factory HP mould, Lee C429-240SWC. (Single Cavity fixed pin Hollow Point GC mould) Pardon my poor pictures, but mine looks like this:
    13 replies | 569 view(s)
  • Bullwolf's Avatar
    06-29-2017, 12:40 AM
    Those look pretty darn good to me. Congratulations. Now the addiction begins. - Bullwolf
    16 replies | 690 view(s)
No More Results
About Bullwolf

Basic Information

About Bullwolf
California/Nevada border


Total Posts
Total Posts
Posts Per Day
Total Albums
Total Photos
General Information
Last Activity
Today 08:42 PM
Current Activity
Viewing Thread Inconsistent primer pockets
Join Date
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check