Inline FabricationMidSouth Shooters SupplyTitan ReloadingWideners
RepackboxLee PrecisionStainLess Steel MediaRotoMetals2
Graf & Sons
Tab Content
  • BK7saum's Avatar
    10-18-2018, 06:58 AM
    I purchased a shim spacer set from Amazon for adjusting die height. My spacers are a smaller, thinner set. I Havent used them much yet , but wasnt ver expensive. Mcmaster-Carr sells shim spacer sets for about $16 that contain 18 spacers from...
    8 replies | 225 view(s)
  • BK7saum's Avatar
    10-15-2018, 04:42 AM
    The full twist will even out the chamfer but you will likely have a sharp or knife edge case mouth. The twisting of the case does even the chamfer though.
    7 replies | 263 view(s)
  • BK7saum's Avatar
    10-12-2018, 08:05 PM
    Yeah, I'd like to see pics of your process. Here is a pdf link to a bunch of different sized templates. I have referenced it in the past to make baffles. ...
    6 replies | 324 view(s)
  • BK7saum's Avatar
    10-09-2018, 03:31 PM
    I weigh my BH 209 on a powder scale and carry charges in pre-measured vials. The conversion is 100:70 or 100 grains by volume = 70 grains by weight. Here is the copy and pasted info from the top of the load data sheet. Volumetric...
    9 replies | 314 view(s)
  • BK7saum's Avatar
    10-08-2018, 12:48 PM
    I keep my bulk powder in an ammo can with a dessicant canister. My individual shaking containers are airtight with an o-ring seal. Rubbermaid Easy Find Lids Tabs Food Storage Container. I PC'd some bullets yesterday with Smoke's powder that...
    13 replies | 470 view(s)
  • BK7saum's Avatar
    10-07-2018, 09:22 PM
    I have a m&p 340 PD. Well, it's my 2nd one. S&W replaced the first. I had an issue with the B/C gap wider at the bottom than the top, but the main problem was the cylinder would slip past the stop on the frame when I tried to eject the cases. Not a...
    11 replies | 426 view(s)
  • BK7saum's Avatar
    09-30-2018, 10:36 PM
    BK7saum replied to a thread .50 Peacekeeper in Cast Boolits
    I have the .50 razorback coming soon. Its a straight walled 300 RUM case chopped to 2.375" for .510 bullets. I have the 513-580 mold that i plan to use as well as the 513-888, some M8 API and possibly some tracer. I also have the MP 640 profile...
    10 replies | 439 view(s)
  • BK7saum's Avatar
    09-27-2018, 12:06 PM
    Yes, as long as headspace is set for a crush fit, just shoot regular 6mm loads. Ill second that necking down 270 or 3006 might cause you to need to ream or neck turn.
    8 replies | 337 view(s)
  • BK7saum's Avatar
    09-26-2018, 09:27 AM
    I would like a 4 cavity with all pins - Plain Base BK7saum bradleyk4860 A T gmail D O T com
    109 replies | 8604 view(s)
  • BK7saum's Avatar
    09-26-2018, 09:23 AM
    BK7saum replied to a thread WTB .32 cal mold in Swappin & Sellin
    This one might be your best bet. It is getting close to production and will fit the S7. I have the 640 MP designs and IIRC, the 115 grain fits the S7 cylinder with no room to spare. The 105 grain version does fine. Most molds in the weight range...
    8 replies | 287 view(s)
  • reed1911's Avatar
    09-26-2018, 03:53 AM
    I'll take 'em. PM To you.
    4 replies | 425 view(s)
No More Results
About BK7saum

Basic Information

About BK7saum
Location:
oklahoma
Interests:
shooting hunting reloading and i fish too.
Occupation:
law enforcement

Statistics


Total Posts
Total Posts
1,478
Posts Per Day
0.53
General Information
Last Activity
Today 12:22 AM
Join Date
03-10-2011
Referrals
0

1 Friend

  1. reed1911 reed1911 is offline

    Boolit Buddy

    reed1911
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check