Inline FabricationStainLess Steel MediaRotoMetals2Titan Reloading
Lee PrecisionWidenersGraf & SonsMidSouth Shooters Supply

Tab Content
  • Keith's Avatar
    09-15-2018, 04:53 PM
    Keith replied to a thread Who likes 22 Short? in Rimfire Area
    I read somewhere recently that shorts are getting phased out. They are already getting hard to find here in Oz. One of our club members just bought a target pistol chambered for shorts and he is worried he bought a lemon. I guess it could be...
    43 replies | 707 view(s)
  • Keith's Avatar
    09-01-2018, 05:22 PM
    Chris, Thanks for that. I have noticed my Lyman Case trimmer does seem give variations in length. I do have some short cases. Keith
    91 replies | 2292 view(s)
  • Keith's Avatar
    08-31-2018, 06:21 PM
    I did the same thing. Sized down some 45-90 for a home made 40-90. I did not anneal, I lost a lot of cases just like that. I have not shot it since but I have 100 sized new cases that I will anneal now but it may be too late. We will see. Must add,...
    14 replies | 709 view(s)
  • Keith's Avatar
    08-31-2018, 06:07 PM
    Its an old Navy Arm Rolling Block that was 45.70 for greasers that I rechambered with the PP reamer. The brass is RP that I had for the old chamber so full length sized it and fireformed.I havnt used new brass yet. I load with 85 grns of 2F Swiss...
    91 replies | 2292 view(s)
  • Keith's Avatar
    08-30-2018, 04:55 PM
    No on annealing and yes on the wad. Once its fireformed apart from cutting a bevel on the mouth I dont touch them again. Just load , shoot , tumble clean, reload.
    91 replies | 2292 view(s)
  • Keith's Avatar
    08-29-2018, 06:01 PM
    I bought a Manson reamer for my 45-70. I believe its a Dan T design for PP . Its shooting better than I ever did with GG. What is the difference with it to one of Brents designs? I have a Green Mountain 16 twist 40 cal barrel here that I would...
    91 replies | 2292 view(s)
  • Keith's Avatar
    08-22-2018, 07:08 PM
    I still have this old one. Last used when I was a kid back in the 50,s. The grounds of the Presbyterian church in Alexandra, Central Otago NZ had this huge Pine tree that was cut down. To split the trunk up they used this. I was sent up to Walls...
    22 replies | 1421 view(s)
  • Keith's Avatar
    08-21-2018, 10:35 PM
    I drilled a hole in the back of an old case, put the bullet it the case and poke the rod in there to push the bullet into the lands , then mark the rod. Works for me because the breech end has been drilled. I think its a good mod because all my...
    56 replies | 11987 view(s)
  • Keith's Avatar
    08-21-2018, 05:27 PM
    As Dan said , I think my base is in the shoulder when the nose is pushed back by the rifling. I have ordered a shorter mold.
    56 replies | 11987 view(s)
No More Results
About Keith

Basic Information

About Keith
Location:
Queensland Australia

Statistics


Total Posts
Total Posts
94
Posts Per Day
0.03
General Information
Last Activity
Yesterday 05:07 PM
Join Date
02-22-2011
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check