ADvertise hereInline FabricationRotoMetals2Titan Reloading
MidSouth Shooters SupplyRepackboxLee PrecisionWideners

Tab Content
  • Larry Gibson's Avatar
    Today, 05:51 PM
    That is also a symptom the spring is in backwards and/or upside down.
    2 replies | 52 view(s)
  • tomme boy's Avatar
    Today, 05:26 PM
    Lee finally released the instructions for the APP. Looks like they want you to buy an extra adapter if you are using a universal decapping die for 22cal. And they also say it is not recommended to size bottle next cartridges with the pass through...
    194 replies | 12947 view(s)
  • Outpost75's Avatar
    Today, 05:24 PM
    Excellent question. Most commercial cast bullets and factory "cowboy" loads are assembled with hard-cast bullets because the 92Pb-6Sb-2Sn, 16 BHN alloy, is readily available in 1-ton heat lots from the lead producers, the material flows well through...
    1 replies | 50 view(s)
  • Outpost75's Avatar
    Today, 02:27 PM
    Order a mold to cast bullets THROAT diameter, NOT barrel groove. Cast your chamber. Read the sticky. Most likely you will need a bullet closer to .315-.316 rather than .313-.314" NOE and Accurate both make suitable molds of adequate...
    1 replies | 28 view(s)
  • lar45's Avatar
    Today, 01:24 PM
    I have web space available, depending on the size of the files, I should be able to put it up if anyone has copies. I couldn't find Wiljen in the list of members to send a PM to. Does anyone have a contact email for him that they could PM to me?
    5 replies | 427 view(s)
  • rockrat's Avatar
    Today, 10:38 AM
    rockrat replied to a thread Duck shot in Lead and Lead Alloys
    I still have some Magnum #2's left over from my crow shooting days. I have used some to alloy lead, it does take awhile to melt, but it finally does, so not too bad. Probably never use it all in my lifetime.
    14 replies | 603 view(s)
  • lar45's Avatar
    Today, 09:05 AM
    Country Gent, a pic of your setup would be great to see.
    14 replies | 589 view(s)
  • BNE's Avatar
    Today, 07:11 AM
    BNE replied to a thread How accurate is a pistol? in Cast Boolits
    Every pistol I own is more accurate than I am. I really think they just take more effort to hold steady and to aim than a rifle that is designed to be held more securely. Iron sights that are only 4 inches apart are difficult to properly line up at...
    31 replies | 397 view(s)
  • BNE's Avatar
    Today, 07:01 AM
    BNE replied to a thread Shipping Primer Dilemmas in Our Town
    I wish you were close! But I think offering what you have for sale here and doing the sale face to face is your best option.
    11 replies | 428 view(s)
  • rockrat's Avatar
    Today, 01:00 AM
    I will take the 311644. PM sent
    1 replies | 176 view(s)
  • Outpost75's Avatar
    Yesterday, 11:16 PM
    Any bolt .30-'06 which feeds and goes bang with factory ammo in which the bullets don't keyhole at 100 yards is worth that.
    45 replies | 2385 view(s)
  • Outpost75's Avatar
    Yesterday, 11:14 PM
    Yes, by making a tapered bump die cut with the same throater used to fit the barrel. Or better yet, just cut a mold to produce a tapered nose to fit the throat. Tom Ellis at Accurate Molds does this routinely on my designs. Send him an upset...
    13 replies | 411 view(s)
  • Outpost75's Avatar
    Yesterday, 11:11 PM
    Outpost75 replied to a thread Powley psi Calculator in Our Town
    ^^^^What Larry said^^^^ What most amused me when visiting BRL on a project back in the 1970s, we were discussing how to measure nutation and precession on a projectile, calculating yaw drag and gyroscopic stability factor, Dr. Robt. L. McCoy...
    6 replies | 185 view(s)
  • tomme boy's Avatar
    Yesterday, 11:01 PM
    WELL?:popcorn:
    12 replies | 472 view(s)
  • BNE's Avatar
    Yesterday, 10:16 PM
    its a good del, I just don't need them. Free bump.
    3 replies | 344 view(s)
  • Larry Gibson's Avatar
    Yesterday, 08:37 PM
    The measured (Oehler M43 PBL) BC of the Lyman 266455 out of a 6.5 Swede runs .255 - .259.
    7 replies | 154 view(s)
  • Larry Gibson's Avatar
    Yesterday, 08:27 PM
    Back in the late '60s when I began studying ballistics (all 3 phases) I got the Dupont charts, the Powley computer and Speer's ballistic computer. All were useful at the time but I quickly learned that the more accurate I was in input the more...
    6 replies | 185 view(s)
  • Larry Gibson's Avatar
    Yesterday, 07:13 PM
    Larry Gibson replied to a thread Arizona in Our Town
    Lake Powell, Lake Roosevelt, Lake Havasu.....the Colorado River......lots of fishing and boating. Bass Pro tournaments on Lake Havasu so fishing can't be that bad.....
    14 replies | 350 view(s)
  • lar45's Avatar
    Yesterday, 06:33 PM
    I'm sorry, I didn't realize that you were looking for 900fps. I gave you everything that you were not looking for, lol. Anyway, 357 mag 4" barrel, Quickload 5.5", Cartridge overall length 1.395" 130gn Boolit length, .605", 357magnum brass:...
    11 replies | 354 view(s)
  • Larry Gibson's Avatar
    Yesterday, 06:20 PM
    I dealt a lot with Olympic Arms ARs back in '91 through 2007 as I lived only a few miles from them in Washington State. Basically the ARs actually built and assembled by them in house were as serviceable as any other ARs. However, they sold a lot...
    8 replies | 263 view(s)
  • Larry Gibson's Avatar
    Yesterday, 05:59 PM
    I've been shooting cast bullets in numerous 22 Hornets for 45+ years. The problem with the 22 Hornet and cast is the different twists used over the years. I've shot cast in 12, 14 and 16" twist barrels. The one cast bullet that has performed...
    12 replies | 238 view(s)
  • Larry Gibson's Avatar
    Yesterday, 05:37 PM
    The WFN GC'ed bullet cast of 16-1 alloy will give all the penetration needed or wanted. No, expansion is not "needed" but it kills quicker. That may be of benefit in thick stuff in Florida as it was in thick stuff where I hunt simply because the...
    12 replies | 319 view(s)
  • Outpost75's Avatar
    Yesterday, 05:36 PM
    The .38 Special wadcutters ordinarily do not produce linear dispersion when target range increases very much beyond about 50 yards or meters, when shot from the standard S&W 18-3/4” twist barrel. Using a faster twist of rifling, such as the 1:10”...
    20 replies | 465 view(s)
  • Outpost75's Avatar
    Yesterday, 03:01 PM
    Thanks for the independent validation. Our men will fight with heroism and honor, as they always do. That alone does not yield victory. Life in combat arms business doesn't require a refined persona, but blunt honesty and the iron will to do what...
    45 replies | 1155 view(s)
  • tomme boy's Avatar
    Yesterday, 02:52 PM
    tomme boy replied to a thread Ar ?? in Military Rifles
    PSA upper have had a problem on and off again where the recess is not milled deep enough for the charging handle to latch. Simple fix on your own or send it back to PSA for replacement. They have lifetime warranty and will pay shipping both ways. ...
    19 replies | 1054 view(s)
  • lar45's Avatar
    Yesterday, 02:18 PM
    You are not going to have a catastrophic failure by running standard 45 Colt loads in a 454 case at 45 Colt length in a 454 gun. By seating the bullet deeper into the 454 case you will probably end up with a very slightly smaller case capacity than...
    14 replies | 214 view(s)
  • Outpost75's Avatar
    Yesterday, 01:48 PM
    Outpost75 replied to a thread .303 MG round???? in Vintage Ammo
    Possibly correct, but does not resemble Pakistani which has POF arsenal code in Roman letters
    6 replies | 239 view(s)
  • Outpost75's Avatar
    Yesterday, 11:30 AM
    If you are not shooting these in an antique revolver, but in a modern revolver chambered for .38 Special, the 12,000 psi pressure limit does not apply. Instead look at starting, pressure-tested loads for the .38 Special and match the same overall...
    6 replies | 102 view(s)
More Activity
About MBTcustom

Basic Information

About MBTcustom
Biography:
I have been casting lead since i was 12, im an active member of the nra and a master Mason.
Location:
Arkansas
Interests:
archery, guns, leather, knives, fishing, hunting, and banjo
Occupation:
I am a Machinist

Signature


Precision in the wrong place is only a placebo.

Statistics


Total Posts
Total Posts
6,990
Posts Per Day
2.15
Albums
Total Albums
4
Total Photos
0
General Information
Last Activity
01-18-2020 12:17 PM
Join Date
02-21-2011
Referrals
7

33 Friends

  1. Alvarez Kelly Alvarez Kelly is offline

    Boolit Master

    Alvarez Kelly
  2. Artful Artful is offline

    Boolit Grand Master

    Artful
  3. Bad Water Bill Bad Water Bill is offline

    Boolit Grand Master

    Bad Water Bill
  4. Ben Ben is offline

    Boolit Grand Master

    Ben
  5. Bjornb Bjornb is offline

    Boolit Master

    Bjornb
  6. BNE BNE is offline

    Boolit Master

    BNE
  7. Brice1985 Brice1985 is offline

    Boolit Mold

    Brice1985
  8. Confederate.45 Confederate.45 is offline

    Boolit Mold

    Confederate.45
  9. felix felix is offline

    Boolit Master on Heavens Range

    • Send a message via AIM to felix
    felix
  10. Fishman Fishman is offline

    Boolit Master

    Fishman
Showing Friends 1 to 10 of 33
Page 1 of 4 1234 LastLast
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check