MidSouth Shooters SupplyLee PrecisionTitan ReloadingInline Fabrication
Graf & SonsStainLess Steel MediaWidenersRotoMetals2

  • AntiqueSledMan's Avatar
    09-17-2018, 06:41 PM
    Hello PBSmith, I use the RCBS 32-170-FN for my 32-40, personally I wouldn't use anything except a flat nose in a tube magazine. AntiqueSledMan.
    4 replies | 116 view(s)
  • AntiqueSledMan's Avatar
    09-16-2018, 06:46 AM
    Hello Inveness, I measured a few top punches, this should work for you. AntiqueSledMan.
    2 replies | 109 view(s)
  • AntiqueSledMan's Avatar
    09-15-2018, 07:14 PM
    This is from the Handloader's Manual of Cartridge conversion. AntiqueSledMan.
    8 replies | 152 view(s)
  • AntiqueSledMan's Avatar
    09-10-2018, 06:00 AM
    Hello DonMountain, People are constantly calling the "Lee Carbide Factory Crimp Die" a "Lee Factory Crimp Die", the attachment shows the difference. The Carbide Factory Crimp Die resizes the cartridge after seating & crimping, it's nothing more...
    21 replies | 678 view(s)
  • AntiqueSledMan's Avatar
    09-02-2018, 07:04 AM
    Hello leadhead, As far as I know the 7.65x53 and the 7.65x54 are the same cartridge. All I have shot through my 91 Mauser is formed military 30-06 brass. I ran them through a Redding 7.65 Belgian Trim Die, then through the Lyman 7.65...
    5 replies | 276 view(s)
  • AntiqueSledMan's Avatar
    08-29-2018, 07:12 AM
    Guesser and Der Gebirgsjager, The Blue Book of Gun Values does list the model 54 as original model 94, the 100 as original model NM94. Numrich Gun Parts cross over is about the same (not much help). The whole purpose of this survey is to find...
    10 replies | 623 view(s)
  • AntiqueSledMan's Avatar
    08-28-2018, 12:57 PM
    Shawlerbrook, Model 45 as in the Big Book was available in 30-30 & 35 Rem. and was listed from1958 to 1965. Both Models, 103.450 & 103.451 were manufactured by Marlin (336). I have seen the 103.450 stamped “J.C. Higgins Model 45” in both Block...
    10 replies | 623 view(s)
  • AntiqueSledMan's Avatar
    08-28-2018, 10:13 AM
    Hello All, Apparently no interest in this topic as I have received no replies to the survey. So I'm removing it from the forum as previously mentioned. Thanks to all, AntiqueSledMan.
    10 replies | 623 view(s)
  • AntiqueSledMan's Avatar
    08-25-2018, 04:54 PM
    Hello wquiles, Very interesting project, nice job. But I feel I must tell you to be sure & count your fingers both before & after using that air over hydraulic cylinder powered ram. With a handle, one can stop the motion of the press when you...
    129 replies | 6853 view(s)
No More Results
About AntiqueSledMan

Basic Information

Statistics


Total Posts
Total Posts
67
Posts Per Day
0.02
General Information
Last Activity
Today 06:53 PM
Join Date
02-20-2011
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check