MidSouth Shooters SupplyInline FabricationADvertise hereLee Precision
Titan ReloadingStainLess Steel MediaGraf & SonsRotoMetals2

Tab Content
  • swheeler's Avatar
    07-20-2018, 02:52 PM
    I thought the color around the 231 was blue in the good old days?
    10 replies | 818 view(s)
  • swheeler's Avatar
    07-18-2018, 08:39 PM
    Dang you sound like Dennis Marshall! ;-)
    25 replies | 504 view(s)
  • swheeler's Avatar
    07-18-2018, 07:36 PM
    The part of the extractor that folds down over the face of the bolt is the CLAW on a claw extractor, the bevel is the bottom edge of that claw that slips into the extractor groove of the cartridge, notice the shape, very very little at a time.
    34 replies | 418 view(s)
  • swheeler's Avatar
    07-18-2018, 07:27 PM
    I've done a couple from BLANKS and they needed extra work to be 100% To tight or not enough rounded off on lower corner, feeding issue, too loose and you are screwed, it can jump the extractor over the rim and you can run it like a push feed, not...
    34 replies | 418 view(s)
  • swheeler's Avatar
    07-18-2018, 07:14 PM
    Look directly at the face of the extractor, head on if you will, you will see the bevel on the edge of the extractor. That bevel is what slips into the extractor groove on the cartridge. After you get the extractor to fit down in to the groove in...
    34 replies | 418 view(s)
  • swheeler's Avatar
    07-18-2018, 05:48 PM
    This is the best I can do with cell phone. Bolt is in same position as your picture, no cartridge under claw as yours, note the extractor to bolt interface, that is what it should look like. I hope this helps you
    34 replies | 418 view(s)
  • swheeler's Avatar
    07-18-2018, 05:31 PM
    Yes and then the bevel on the claw to cartridge head, the cartridge should slip under the extractor with enough force to hold the cartridge in place-CRF. make sure the collar wraps around the groove in the bolt as a slip fit also, especially if...
    34 replies | 418 view(s)
  • swheeler's Avatar
    07-18-2018, 03:13 PM
    Maybe this will help, maybe not:-) cell phone pictures not too good. SR extractor on bolt and with cartridge under extractor lip. You may have the wrong extractor or one that has never been fit, maybe even an extractor collar that is wrong?
    34 replies | 418 view(s)
  • swheeler's Avatar
    07-18-2018, 02:24 PM
    There's way to much clearance between bolt and bottom of extractor, there is not that much with a cartridge under the lip of one that's correct.
    34 replies | 418 view(s)
  • swheeler's Avatar
    07-18-2018, 02:19 PM
    Yes that looks to high and is causing the bind I would guess, once you fit that correctly then the claw/ bevel will need fit to case head. Where did you get the extractor, one of Midways NEW blanks?
    34 replies | 418 view(s)
  • swheeler's Avatar
    07-18-2018, 12:41 PM
    Sounds like a blank new extractor that has not been fit to case head yet?
    34 replies | 418 view(s)
  • swheeler's Avatar
    07-18-2018, 12:37 PM
    I use a 5 gal bucket with about 4 gal of water in it. I float 7-8 small wet Dollar Store sponges on top of the water, a bullet just tips the sponge and dumps. If you do slash water in a cavity it is gone instantly anyway so no worries.
    25 replies | 504 view(s)
  • swheeler's Avatar
    07-17-2018, 02:23 PM
    I've been using it with powder coated gas checked bullets for 3 years now according to the 2015 date on the HBN bottle. I've also added to lube(no value I could determine) and used on a patch to condition the bore, helped with getting HBN back into...
    3 replies | 129 view(s)
  • swheeler's Avatar
    07-17-2018, 01:54 PM
    I tried it in 30-06 with 200 gr Lee bullet, nice mild load and reasonably accurate for conditions that day. 15.0 grs was most accurate of 14-16 tested, 5 round groups of 1.5"-100yd @ 10*F Jan 2004, 15.0=1556 fps from 22" Savage 110. WSF(15.0=1555...
    6 replies | 216 view(s)
  • swheeler's Avatar
    07-16-2018, 09:35 AM
    Very nice JB, enjoy it. I made one years ago so the wife and I could get away from the crowds at the range and love it.
    17 replies | 744 view(s)
No More Results
About ColColt

Basic Information

About ColColt
Biography:
I got into relaoding in 1969 but casting bullets came later...around 1975.
Location:
South East
Interests:
Photography, Reloading, Pistol Shooting
Occupation:
Elect. Design Engineering

Signature


NRA Patron Member

Kids Are For People That Can't Have Dogs

Statistics


Total Posts
Total Posts
2,167
Posts Per Day
0.79
General Information
Last Activity
10-11-2015 08:09 PM
Join Date
01-28-2011
Referrals
1

1 Friend

  1. swheeler swheeler is online now

    Boolit Master

    swheeler
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check