Inline FabricationMidSouth Shooters SupplyWidenersTitan Reloading
RepackboxADvertise hereRotoMetals2Lee Precision

Tab Content
  • tomme boy's Avatar
    Yesterday, 05:43 PM
    I sprayed all of mine with Moly lube. Takes care of them sticking. One more thing you can check is to make sure your lead is up to the right temp. If the lead is on the colder side of what is needed the bullets can stick from that too.
    9 replies | 177 view(s)
  • tomme boy's Avatar
    Yesterday, 05:35 PM
    tomme boy replied to a thread Group Buy Slow Down in Cast Boolits
    There are issues with MP charging more than the agreed price on buys right now. It has been reported but no updates. About ready to send it to paypal to get resolved. The price was agreed on for shipping included on price given. He is now charging...
    13 replies | 369 view(s)
  • tomme boy's Avatar
    03-27-2020, 09:59 AM
    It should have to go through an importer.
    19 replies | 504 view(s)
  • tomme boy's Avatar
    03-26-2020, 06:04 PM
    Try Shooters World Auto Pistol powder and then say that. It is the finest powder I have ever seen
    20 replies | 412 view(s)
  • tomme boy's Avatar
    03-26-2020, 03:51 PM
    I have both the autodisc and autodrum. The drum leaks BAD. The disc just a very small amount. My RCBS NEVER leaks but I can't set the rcbs to function automatically on my progressive presses. I would have to manually operate the powder throw. The...
    20 replies | 412 view(s)
  • tomme boy's Avatar
    03-25-2020, 01:52 AM
    Fleet and Farm should have it Nodakjohns
    11 replies | 360 view(s)
  • tomme boy's Avatar
    03-25-2020, 01:45 AM
    Just looking up some info about this. If the feds are doing the check, they have 3 business days to approve or deny. If there is not word then the FFL MUST proceed with the transfer. If the state is doing it they have to do the 3 business day...
    27 replies | 1187 view(s)
  • tomme boy's Avatar
    03-24-2020, 05:56 PM
    tomme boy replied to a thread Brass 4 sale in Swappin & Sellin
    btt............
    5 replies | 863 view(s)
  • tomme boy's Avatar
    03-24-2020, 05:43 PM
    You really should not use the old media as a flux in your pot. Even though it is cleaned it will still have a LOT of lead oxides still in the mix. Sure way to get lead poisoning
    8 replies | 184 view(s)
  • tomme boy's Avatar
    03-24-2020, 05:38 PM
    Shoots very well in the 350 Legend.
    6 replies | 201 view(s)
  • tomme boy's Avatar
    03-24-2020, 05:37 PM
    tomme boy replied to a thread Apology in Our Town
    If something you typed pops up as ************************************************ then it is the word filter this forum has to block profanity. Go back and change it before you get caught. Been there!
    18 replies | 831 view(s)
  • tomme boy's Avatar
    03-23-2020, 05:52 PM
    I understand things happen. But this still has not been addressed. If shipping was included then that is the price that must be honored. Look through some of the other group buys and DHL shipping cost is not addressed in any of them either. This...
    204 replies | 21684 view(s)
  • tomme boy's Avatar
    03-23-2020, 02:25 AM
    Was out last week shooting my 8" AR9 a little bit. I was hitting the steel 12"x12" plate at 200 yds almost every shot. I have a cheap $30 2 MOA red dot on it. I had to give it one plate spacing above the plate to hit it. A couple times I went 31 out...
    13 replies | 398 view(s)
  • tomme boy's Avatar
    03-23-2020, 02:06 AM
    I just ordered a WCT Worlds Cheapest Trimmer. We will see how my hands hold up. Going to use my drill press so it will bottom out the case to the table of the press to help hold it.
    27 replies | 735 view(s)
  • tomme boy's Avatar
    03-22-2020, 03:35 AM
    i use the RCBS hand trimmer that I drive with a 1/2" hand drill. I have the 3-way trimmer head on the end. I have a wire wrapped around the trigger to run the drill at about 20% speed. The limiting factor for me is my hands and finger cramping up. I...
    27 replies | 735 view(s)
  • tomme boy's Avatar
    03-21-2020, 09:54 PM
    Post here what you want then send me a PM with what you want. Include your shipping info in the PM. Much easier to tell where it needs to go. A posted I will take it has first dibs. Payment needs to be a USPS MO, Cash at your risk, Check, Paypal...
    5 replies | 863 view(s)
  • tomme boy's Avatar
    03-21-2020, 03:50 PM
    They are Bergara. CVA owns them
    2 replies | 148 view(s)
More Activity
About Mashuga

Basic Information

About Mashuga
Location:
Iowa

Statistics


Total Posts
Total Posts
3
Posts Per Day
0.00
General Information
Last Activity
01-21-2020 05:55 PM
Join Date
12-20-2010
Referrals
0

1 Friend

  1. tomme boy tomme boy is offline

    Boolit Master

    tomme boy
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check