Inline FabricationLee PrecisionMidSouth Shooters SupplyStainLess Steel Media
RotoMetals2Titan ReloadingADvertise hereGraf & Sons

Tab Content
  • blikseme300's Avatar
    09-21-2017, 07:56 PM
    Maybe this can help? https://www.beartoothbullets.com/tech_notes/archive_tech_notes.htm/52
    13 replies | 361 view(s)
  • blikseme300's Avatar
    09-16-2017, 08:52 PM
    I use wood shavings and sawdust when rendering WW's to ingots but bees wax or Ben's Red for my casting pots as I found this kept things cleaner for me. A few years ago I somehow ended up with about 5# of Ben's Red, good lube BTW, so this is what...
    13 replies | 510 view(s)
  • blikseme300's Avatar
    09-14-2017, 01:40 PM
    What I did also. For many rifle loads I use the double disk kit. For tweaking volume I have resorted to 2 methods, a set screw in the cavity wall or rat tail file to enlarge the cavity. Duplicating loads is easy as I document the cavities used. ...
    19 replies | 470 view(s)
  • blikseme300's Avatar
    09-14-2017, 01:15 PM
    I like and use many Lee products but their rifle seaters are not great for cast. Most of my mix-n-match die sets now include a Hornady seater die. With some I needed to modify the sleeve to accommodate the larger diameters that cast require but it...
    12 replies | 365 view(s)
  • blikseme300's Avatar
    09-13-2017, 05:44 PM
    Yep, I'm part of the 99% also. My B&D toaster was $19.99 from Wallyworld. Yes, it is small but works for me as I mainly do rifle CB's in it. Typical loads are 80 x 500gn CB's for my 458WM or 120 x 265gn for my 444 Marlin. I do stand these up on...
    16 replies | 511 view(s)
  • blikseme300's Avatar
    09-10-2017, 09:38 PM
    I'll take the Hornady 6.5 Scan die set. PM on the way.
    2 replies | 427 view(s)
  • blikseme300's Avatar
    09-09-2017, 10:14 AM
    Many good comments here. Something I did not see mentioned is the water quality as this does affect the cleaning. Here the local water is quite hard so I found that I needed to add more Lemishine to get the desired result. The other thing I...
    17 replies | 500 view(s)
  • blikseme300's Avatar
    09-05-2017, 07:02 PM
    One of the often unmentioned advantages of the Star is not needing different top punches to match the CB profiles. Back when I was researching what to buy this factored a lot as I was already quite deep into casting and reloading. The pennies...
    19 replies | 410 view(s)
  • bronte454's Avatar
    09-04-2017, 09:45 PM
    I appreciate the input . Didn't think about the cross pin through the wood . The molds are intact with the bottom retaining screws . Just missing the hollow point pins . Will have to see what I can measure and drill and how accurately . Again thanks
    3 replies | 209 view(s)
  • blikseme300's Avatar
    09-03-2017, 09:00 PM
    I use the Lee 450gn PB and the Lee 500gn GC with my M77. I found that the 450gn over 34gn of SR4759 gives me good accuracy out to 200 yards without discomfort from extended range sessions. CB's are PC'd and sized to .459". I have not tried any other...
    18 replies | 522 view(s)
  • bronte454's Avatar
    09-01-2017, 08:37 AM
    I know this has been discussed somewhere surprised I couldn't find a sticky on the subject. I've bought several lyman and a couple Cramer hollow point molds .that have no pin . I can't afford 40 bucks for each one to send off to Eric at hollow...
    3 replies | 209 view(s)
  • bronte454's Avatar
    08-30-2017, 08:03 AM
    Do not have ANY experience with bear but have plenty with deer . The devistator from 900-1100 with that soft bullet will go through through a deer end to end at least to 90 yards. The hard flat nose that fast just zips through no expansion . Just...
    52 replies | 2061 view(s)
  • blikseme300's Avatar
    08-27-2017, 11:08 PM
    I like your solution for removing the steel clips. Thanks for sharing.
    2 replies | 252 view(s)
  • blikseme300's Avatar
    08-27-2017, 02:13 PM
    I use the RCBS 3-way in my Hornady trimmer and it is the bees knees. The Lee 3-way and the Lyman 3-way did not work as well for me. Yes, just switch out the pilot for different calibers and yes, no need to debur.
    6 replies | 633 view(s)
No More Results
About bronte454

Basic Information

Date of Birth
December 7, 1972 (44)
About bronte454
Location:
Holden Ma
Interests:
shooting stuff

Statistics


Total Posts
Total Posts
98
Posts Per Day
0.04
General Information
Last Activity
09-19-2017 10:04 PM
Join Date
12-20-2010
Referrals
0

2 Friends

  1. blikseme300 blikseme300 is offline

    Boolit Master

    blikseme300
  2. Xcaliber Xcaliber is offline

    Boolit Man

    Xcaliber
Showing Friends 1 to 2 of 2
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check