Inline FabricationTitan ReloadingRepackboxRotoMetals2
Lee PrecisionADvertise hereWideners

Tab Content
  • 44magLeo's Avatar
    02-21-2020, 04:45 PM
    GRMPS, Your copy looks much better than mine. From the look of the pic on the front it looks like it was for a more recent version than the one mine came with. The knocker in the pic looks to be made with a flat steel strap curled for the pivot...
    32 replies | 6040 view(s)
  • 44magLeo's Avatar
    02-20-2020, 11:09 PM
    I found with my Lee Bench Prime tool I have it mounted on a piece of oak board. I just set it on the bench, not clamped in place, and use it. After I place the case in the shell holder I drop my hand down a rest a finger on the board. After I seat...
    59 replies | 5582 view(s)
  • 44magLeo's Avatar
    02-20-2020, 10:35 PM
    I have copies of two 310 die charts. One has a lot more numbers but it only covers the size dies. The other is not so long but list's the cartridge, handles, adapter die, priming chamber, Muzzle sizer/ DA chamber, Expander chamber, Expander for...
    13 replies | 340 view(s)
  • 44magLeo's Avatar
    02-20-2020, 10:16 PM
    44magLeo replied to a thread Lyman 55 in Reloading Equipment
    I tried the acetone. I put about 1/4 inch in a glass jar, just enough to wet the end. It softened the end a bit, then it got brittle and started to crumble and clouded the tube up about an inch. Guess is wasn't acrylic. On the Mothers, I didn't...
    10 replies | 364 view(s)
  • 44magLeo's Avatar
    02-20-2020, 09:50 PM
    I have this set of instructions. It has a hole where it was creased. This hole is by the Hodgen 4831 powder. I found another set of instructions online and it wasn't any easier to read, poor copy. I don't know if this is good or not. Leo
    32 replies | 6040 view(s)
  • 44magLeo's Avatar
    02-20-2020, 09:18 PM
    The reamer I'm sure helped a lot, I think the micrometer seating die helped to. The case trimmer didn't hurt either. On the speed, once you got a lot of cases trimmed and reamed you shouldn't have to do that again for quite a few reloads. I have...
    31 replies | 911 view(s)
  • 44magLeo's Avatar
    02-20-2020, 08:55 PM
    One thing I have found with the collet FCD and the Collet Neck size die is to disassemble, Clean polish the outside of the collect where it touches the body and the inside of the body where it touches the collet. Sometimes there is a burr or other...
    14 replies | 398 view(s)
  • 44magLeo's Avatar
    02-20-2020, 08:15 PM
    Thanks for the advice. I've been casting since 1978. A friend got me started with fishing weights and jigs. That got me into casting for my 44Mag rifle and revolvers. I have been scrounging COWW as well as pure lead , as in lead pipe and sheeting,...
    14 replies | 676 view(s)
  • 44magLeo's Avatar
    02-16-2020, 12:21 PM
    44magLeo replied to a thread Haul post in Lead and Lead Alloys
    I have a cut off propane tank I use with my propane cooker. I might get another and cut both ends off. Weld a flat piece of steel on one end to have a flat bottom. Then build a spout and rod to make it a bottom pour. Maybe even use a electric stove...
    14 replies | 317 view(s)
  • 44magLeo's Avatar
    02-16-2020, 12:03 PM
    I buy some from Ebay if the seller has a lot of good feedback. On here as well as form scrounging, watching the local Want Ad papers. I don't have any luck on Craig's List, Never can get ahold of the sellers. Find a lot laying on the road and...
    18 replies | 431 view(s)
  • 44magLeo's Avatar
    02-16-2020, 11:15 AM
    44magLeo replied to a thread Lyman 55 in Reloading Equipment
    I have some acetone, I mix it 50/50 with ATF, Brand or price don't matter much, to make the best penetrating fluid ever. I'll see how that works. Thanks. Leo
    10 replies | 364 view(s)
  • 44magLeo's Avatar
    02-16-2020, 11:02 AM
    I set mine by setting all the slides to zero. I then open all three most of the way. I then use my scale to get a charge. I pour this charge in the hopper and turn the slides up so the powder gets into the opening. Move the measure around to get all...
    32 replies | 6040 view(s)
  • 44magLeo's Avatar
    02-15-2020, 10:33 PM
    The place I get my propane tanks filled had old tanks setting around. I asked about getting one to cut up. They said sure and even pulled the valve for me. Didn't even charge me for it. Once home I flushed it with the water hose a couple times then...
    22 replies | 746 view(s)
  • 44magLeo's Avatar
    02-15-2020, 09:48 PM
    Instead of using 50 caliber cans you could use 30 caliber cans. Not sure how muchyou can get in the 30 cal; can but would take up less space than a half full 50 cal can. Leo
    28 replies | 927 view(s)
  • 44magLeo's Avatar
    02-15-2020, 08:58 PM
    44magLeo replied to a thread Lyman 55 in Reloading Equipment
    I tried the Goo Gone. It brought up the too worst ones up to a bit darker than the clearest one. Look much better. I still want to use the new clear tubing I have. I bought two pieces of clear tubing. I think they are acrylic. I think I paid $10...
    10 replies | 364 view(s)
  • 44magLeo's Avatar
    02-15-2020, 05:56 PM
    44magLeo replied to a thread Lyman 55 in Reloading Equipment
    I'll have to try that One of mine is so dark you can't see through even with light shining through from behind and another about half that bad. The other is tinted but still ok. Thanks for the tip. I keep the Goo Gone around for a lot of things,...
    10 replies | 364 view(s)
  • 44magLeo's Avatar
    02-15-2020, 05:50 PM
    I was just on the Lee website checking on something I read about on another thread and spotted something. They had a listing for Heavy Duty Guided Decappers. I thought What are those. So I looked them up. Some complain about breaking or bending...
    8 replies | 317 view(s)
  • 44magLeo's Avatar
    02-15-2020, 05:29 PM
    On most auto pistols the cases headspace on the mouth. If you expander flares the cases mouth most use a taper crimp to remove the flare of the mouth down to a certain diameter. Usually just enough so the case is back to a straight wall. This...
    23 replies | 490 view(s)
  • 44magLeo's Avatar
    02-13-2020, 08:48 PM
    I spent some time sorting my lead today. Did the clink-thud test. About 70% clinked. On the solder not all was 50/50. out of the 23 bars some were 9 marked WARRANTED 50/50 with a few also marked GRADE A REPUBLIC on them. 7 had just ALPHA on...
    14 replies | 676 view(s)
  • 44magLeo's Avatar
    02-12-2020, 08:34 PM
    I saw an ad in a local want ad paper. 125 lbs. for $80. When I got down there a lot was in ingots. Some shiny others dull gray. I think the dull ones are pure lead, the shiny WW's. He had some loose WW's in some coffee jugs. I got about 142 lbs...
    14 replies | 676 view(s)
  • 44magLeo's Avatar
    02-12-2020, 08:07 PM
    44magLeo replied to a thread Rcbs rc ii ?? in Reloading Equipment
    I think the early versions had the green cast links. Then the bean counter's decided plain steel links were less expensive. So after that they got the plain steel links. Leo
    4 replies | 284 view(s)
  • 44magLeo's Avatar
    02-12-2020, 07:53 PM
    My vote goes for either the Lyman 55 or the Lee PPM. I have both, 3 of the 55's. The Lee has a rubber grommet thing built in so as the measuring chamber closes it won't cut the powder. I find it very accurate. The 55's can handle larger volumes of...
    20 replies | 528 view(s)
  • 44magLeo's Avatar
    02-09-2020, 07:39 PM
    I have a Lyman for 7,62x54R. I got it because some of the once fired brass I picked up wouldn't chamber without a bit too much effort even after FL sizing. These were a too tight fit in the ammo checker. I bought a Lyman Shell Sizer. Made like the...
    2 replies | 139 view(s)
  • 44magLeo's Avatar
    02-09-2020, 02:40 PM
    I really like JimKirk's idea. I had a Lyman trimmer that worked like that. Figured out the variations I head/rim size caused variations in trim length. I then went with the Lee trimmer. It uses a mandrel to control case length. Found most cases...
    11 replies | 845 view(s)
  • 44magLeo's Avatar
    02-07-2020, 09:23 PM
    I don't own a case tumbler. Had one but didn't like the mess. Clean brass is good. bright and shiny like new is not any better as far as the way it goes through a guns action or how well it performs. If you think your bright and shiny ammo...
    71 replies | 2393 view(s)
  • 44magLeo's Avatar
    02-07-2020, 08:39 PM
    The way Lee's measure has the shut off valve it acts as a powder baffle. This keeps the same amount over the charging chamber of the measure. This helps with consistency. I have one. It has a bit of a learning curve to the adjustments, but is very...
    23 replies | 713 view(s)
  • 44magLeo's Avatar
    02-05-2020, 02:32 PM
    He's a one man shop. Since Lyman quit making these tools he's not been able to make stuff. He probably doesn't have your items in stock and has to make them. This can take awhile. When I ordered the priming chamber and shell adapter for my...
    30 replies | 3209 view(s)
  • 44magLeo's Avatar
    02-04-2020, 04:27 PM
    I don't know what Stoddard Solvent is but the WD in WD40 stands for water dispersant. It's not a lube. It gets water out of the way so the parts can do what they should. When I was a kid most people with Chevy's carried it around with them. If...
    38 replies | 1501 view(s)
  • 44magLeo's Avatar
    02-04-2020, 04:01 PM
    I have some Federal that are that way. On some the ring matches the length of the 180 gr bullet, others the length of the 240 gr bullet. I also think it was for bullet set back, most for Ruger's semi auto carbine in 44 mag. Once you resize then...
    18 replies | 1037 view(s)
  • 44magLeo's Avatar
    02-04-2020, 03:06 PM
    I don't have a metal lathe but do have a wood lathe. To cut an angle on the edges as you want I would just move my cutting tool at an angle to make the cut. I no a bit about metal lathes from high school shop class. Low those many years ago. I know...
    19 replies | 902 view(s)
More Activity
About 44magLeo

Basic Information

About 44magLeo
Biography:
I like cast boolits in my hand guns and rifles.
Location:
Lebanon, NY
Interests:
Motorcycles, shooting, hunting, fishingg
Occupation:
Retired factory worker

Statistics


Total Posts
Total Posts
588
Posts Per Day
0.17
General Information
Last Activity
02-21-2020 05:21 PM
Join Date
12-05-2010
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check