RotoMetals2StainLess Steel MediaGraf & SonsInline Fabrication
Titan ReloadingWisconsin TriggerMidSouth Shooters SupplyLee Precision

Tab Content
  • clodhopper's Avatar
    Yesterday, 10:24 PM
    clodhopper replied to a thread Lead extruder. in Swaging
    That is a very good solution for a high pressure hydraulic pump.
    30 replies | 2229 view(s)
  • clodhopper's Avatar
    07-16-2017, 10:42 PM
    That bullet profile could be duplicated with a small lathe equipped with a tool post grinder. And a cannalure tool for the muzzleloader bullets, the process would not be fast. But considering the cost of those bullets, making your own might be...
    6 replies | 637 view(s)
  • clodhopper's Avatar
    07-15-2017, 11:00 PM
    clodhopper replied to a thread Leaky Maruader in AirGuns
    Still holding pressure good. Have been to busy shooting CMP, and working appleseed to shoot the air gun much.
    8 replies | 476 view(s)
  • bumpo628's Avatar
    07-15-2017, 09:50 PM
    That is due to the limitations of the hardness formula. It is really only valid with tin and antimony percentages found in boolit alloys. The formula produces good values when both Sn and Sb are higher that about 1%, but not higher than about 6%. ...
    261 replies | 158136 view(s)
  • clodhopper's Avatar
    07-13-2017, 09:44 AM
    Nice target, I will shoot some more of your pellets after I get my scope mounted square again. For best results do not let target turrets bang against steel pellet trap...
    4 replies | 252 view(s)
  • obssd1958's Avatar
    07-12-2017, 10:29 PM
    Looking for something like these? If you're just using them for a display for a few days, I would be happy to send them to you for just the cost of a small flat rate box, as long as you send them back when you're done. Let me know! Don
    9 replies | 483 view(s)
  • obssd1958's Avatar
    07-12-2017, 10:19 AM
    I'm in at $100
    15 replies | 1144 view(s)
  • clodhopper's Avatar
    07-09-2017, 01:54 PM
    D-RIG kindly sent me some of his swaged .25 air rifle pellets. We visited on the phone and I told him I had a Marauder PCP 25 caliber rifle. MY results at 31 yards yielded 3 groups of five, about .65", My one comparable group today with...
    12 replies | 826 view(s)
  • obssd1958's Avatar
    07-07-2017, 10:47 AM
    Newtire, I have a mould for a hollow base, smooth sided, slug (drops at @.395), that I'm sending your way this morning. There are two different pins for the hollow base. I think it was designed for the .410 shotgun, but after reading your...
    10 replies | 369 view(s)
  • clodhopper's Avatar
    07-05-2017, 09:08 AM
    clodhopper replied to a thread Leaky Maruader in AirGuns
    I had given some thought to smearing a little spit over the fill nipple, like checking a leaky valve on a car tire. But read online about the importance of keeping PCP guns dry inside. Really, throwing the gun in the bath tub will make the leaks...
    8 replies | 476 view(s)
  • bumpo628's Avatar
    07-04-2017, 02:20 PM
    Try to "save as" a new file. That should remove the read only issue.
    261 replies | 158136 view(s)
  • obssd1958's Avatar
    07-04-2017, 01:41 PM
    obssd1958 replied to a thread WTS-270 brass in Swappin & Sellin
    I'm your huckleberry... I'll take the brass. PM on it's way, with my shipping address. Don (and no, I don't currently have a .270........) ;)
    7 replies | 412 view(s)
  • clodhopper's Avatar
    07-03-2017, 05:08 PM
    clodhopper replied to a thread Leaky Maruader in AirGuns
    Still holding 3000 psi, must be okay. Look out starlings!
    8 replies | 476 view(s)
  • clodhopper's Avatar
    07-02-2017, 05:28 PM
    clodhopper started a thread Leaky Maruader in AirGuns
    Last night after shooting a few rounds, I pumped up my .25 Mrod. Checking the pressure later it was down 500 lbs. An hour later it was down another 500 psi. By this morning the gauge read 0. So, thinking it was the check valve on the fill end....
    8 replies | 476 view(s)
  • clodhopper's Avatar
    07-01-2017, 04:30 PM
    Glad to see you here, really want to know more about your pellet swaging. I have a .25 marauder, and am making chips plus bigger pieces of scrap from 01 tool steel in attempts at a 25 caliber pellet swage die.
    12 replies | 826 view(s)
No More Results
About *Paladin*

Basic Information

About *Paladin*
Location:
Idaho
Occupation:
USAF Security Forces/Combat Arms Instructor

Signature


-Steve
Have gun, will travel.
Iraq Vet '05-'06
Afghanistan Vet '09-'10
RIP- TSgt Jason Norton and SSgt Brian McElroy, KIA 22 Jan '06, near Taji, Iraq. You'll never be forgotten.

Statistics


Total Posts
Total Posts
460
Posts Per Day
0.19
General Information
Last Activity
06-08-2014 09:13 PM
Join Date
11-27-2010
Referrals
0

8 Friends

  1. bumpo628 bumpo628 is offline

    Boolit Master

    bumpo628
  2. clodhopper clodhopper is offline

    Boolit Master

    clodhopper
  3. linotype linotype is offline

    Boolit Master

    linotype
  4. MtJerry MtJerry is offline

    Boolit Master

    MtJerry
  5. obssd1958 obssd1958 is offline

    Boolit Master / Honcho

    obssd1958
  6. RANGER RICK RANGER RICK is offline

    Boolit Master

    RANGER RICK
  7. THOR5624 THOR5624 is offline

    Boolit Mold

    THOR5624
  8. TonyM TonyM is offline

    Boolit Man

    TonyM
Showing Friends 1 to 8 of 8
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check