Lee PrecisionRotoMetals2ADvertise hereMidSouth Shooters Supply
Graf & SonsInline FabricationStainLess Steel MediaTitan Reloading

Tab Content
  • dk17hmr's Avatar
    05-16-2018, 05:23 PM
    Were you patterning your barrels on a larger target or just shooting at a 10" target? I have been playing with a 10 pellet load in various shotguns with various barrel lengths and chokes. My over under with a full choke is keeping all or almost...
    4 replies | 194 view(s)
  • dk17hmr's Avatar
    05-14-2018, 05:22 PM
    There has been some chatter on various forums about the high velocity buckshot loads on page 35 in the IMR manual. http://pdf.textfiles.com/manuals/FIREARMS/imr_reloading.pdf I had all the components on hand except for the buffer. I did a...
    1 replies | 129 view(s)
  • dk17hmr's Avatar
    05-08-2018, 01:31 PM
    I'd powder coat and shoot without a gas check if it were me. My cans took to long to get and cost to much money to let a little piece of metal that is useless on a sub sonic round ruin it.
    9 replies | 2956 view(s)
  • dk17hmr's Avatar
    05-08-2018, 12:33 PM
    They are all plastic with a high brass base. I'm wanting to try a 10 pellet load of 000.
    2 replies | 150 view(s)
  • dk17hmr's Avatar
    05-08-2018, 11:00 AM
    I picked up a bunch of these hulls at the local trap club yesterday. I was messing with them a little bit last night and found that if you cut the petals off of a CB1138-12 you can easily get 10 pellets of 000 in the hull stacked by twos and it...
    2 replies | 150 view(s)
  • dk17hmr's Avatar
    05-05-2018, 07:12 PM
    There is a 12 pellet load in the Lyman manual for federal gold metal hulls and a WAA12R wad with 34.0gr of bluedot. It does fit I just loaded one but the hull is dimpled. I pulled it apart and cut the petals off and it fits allot better. I'll...
    5 replies | 428 view(s)
  • dk17hmr's Avatar
    05-05-2018, 09:24 AM
    I do that next county stuff also, depends if they are skittish, I have killed them with a muzzleloader they just need to be in curious mood.
    4 replies | 261 view(s)
  • dk17hmr's Avatar
    05-04-2018, 11:39 PM
    So does the exact buffer matter? It says BP SDC in that load data....would BPI original or #47 work? I'd like to try a high velocity load to see how my shotguns like it and maybe use it for coyotes and antelope.
    4 replies | 261 view(s)
  • dk17hmr's Avatar
    05-04-2018, 10:45 AM
    Can you get 12 in a 2 3/4" hull? I have a 10 pellet load and it's a full load.
    5 replies | 428 view(s)
No More Results
About dk17hmr

Basic Information

Date of Birth
October 27, 1986 (31)
About dk17hmr
love shooting, reloading, and hunting
Hunting, Fishing, Shooting
Construction Materials Tester


.................................................. ........................................
Sticks and stones may break my bones but hollow points expand on impact.

Taxidermists are cheaper than surgeons....keep shooting


Some people measure success in Minutes of Angle


Total Posts
Total Posts
Posts Per Day
Total Albums
Total Photos
General Information
Last Activity
Yesterday 04:16 PM
Join Date
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check