RotoMetals2Titan ReloadingMidSouth Shooters SupplyInline Fabrication
StainLess Steel MediaLee PrecisionADvertise hereGraf & Sons

  • Good Cheer's Avatar
    Today, 09:04 AM
    The arguments arise from preference for claiming that chain fires occur only through ignition from either the front or the rear. No one who hasn't staked out a position should take either to heart before ruminating on the likelihood that ignition...
    29 replies | 884 view(s)
  • Good Cheer's Avatar
    Yesterday, 07:06 PM
    Heh, I expect this is going to be some kind of fun shooter. REAL's, round ball, minies, maxihunters, lubed, paper patched, plenty of molds to play with.
    8 replies | 391 view(s)
  • Good Cheer's Avatar
    Yesterday, 07:00 PM
    I'll a picture worth a thousand words some day soon. Don't hurt yourself.
    8 replies | 391 view(s)
  • Good Cheer's Avatar
    Yesterday, 03:52 PM
    Needed #8-36 screws for the threaded scoping mounting holes. Ended up had to get 3/4" long and work the length down to fit the holes and the thickness of metal on the mounts. And the socket heads were too big in diameter to fit in the countersinks...
    8 replies | 391 view(s)
  • Good Cheer's Avatar
    Yesterday, 10:06 AM
    Yep, just gonna have to try it and see. Being a TC all I have to do is drill holes through socket head set screws to make a handful of flash hole liners. Hopefully the lateral thrust from the flash hole will not require windage...
    10 replies | 410 view(s)
  • Good Cheer's Avatar
    01-16-2018, 10:07 AM
    My catchers tend to be temporary constructs fabbed from castaway materials. If a sample needs to be recovered for examination something gets cobbled together like milk jugs of water backed by either soaked bundles of waste paper, shredded paper or...
    31 replies | 1686 view(s)
  • Good Cheer's Avatar
    01-16-2018, 07:03 AM
    I use a 9/16" gasket punch. How well your wads work will depend some on what you make them out of, how deep the rifling is, dry or lubed or soaked, all that jazz. Something I've tried is that spongy paper stuff that egg cartons are made of....
    4 replies | 210 view(s)
  • Good Cheer's Avatar
    01-14-2018, 07:13 PM
    Just put the letter in the envelope urging them to produce the steel receiver in .41 Magnum.
    39 replies | 2946 view(s)
  • Good Cheer's Avatar
    01-13-2018, 07:10 PM
    Well, what I been thinking is that when I get on out there distance wise the small differences will be magnified just like with any reloads. And that the flinter flash hole is large enough to produce substantial back flow which will not behave in...
    10 replies | 410 view(s)
  • Good Cheer's Avatar
    01-13-2018, 03:59 PM
    Hey there. Just asked 'cause I'm working towards getting a fast twist flinter working. I'm anticipating variations in elevation due to irregular back flow. But puffs in the puddin' so we'll see. And my new glasses should be in next week so maybe I...
    10 replies | 410 view(s)
  • Good Cheer's Avatar
    01-13-2018, 07:25 AM
    Are you seeing any significant vertical stringing at longer ranges?
    10 replies | 410 view(s)
  • Good Cheer's Avatar
    01-11-2018, 10:11 AM
    Has anyone concocted a specialty boolit / over all length loading to provide an improvement in .45 accuracy with the Judge type revolvers? A cousin has purchased one and it's got me wondering what would work better. Extended brass and hollow...
    25 replies | 614 view(s)
  • Good Cheer's Avatar
    01-09-2018, 04:15 PM
    To each his own. For a cast bullet deer rifle I designed for accuracy and excess power for 200 yards, my personal shooting accuracy limitation in the field. Turned out I never dropped one past 130.
    123 replies | 3656 view(s)
  • Good Cheer's Avatar
    01-09-2018, 11:35 AM
    I've tried various combinations trying to get Green Mountain .40 barrels to shoot other than round ball, with varying degrees of success. Lubed lead, paper patched, more powder, less powder... Getting consistent enough results just never happened:...
    6 replies | 205 view(s)
  • Good Cheer's Avatar
    01-08-2018, 10:08 PM
    Oh my, that sounds like a paper patch waiting to happen!
    14 replies | 386 view(s)
  • Good Cheer's Avatar
    01-08-2018, 09:55 PM
    On small diameters the flat moving a little bit towards the center rather than being tangential makes for an oddly flying projectile. In a percussion revolver maybe it wouldn't matter? I'd rather smoosh a sprue under the plunger.
    11 replies | 289 view(s)
  • Good Cheer's Avatar
    01-07-2018, 08:34 PM
    What's the biggest diameter boolits you can chamber in your 25-35?
    2 replies | 131 view(s)
  • Good Cheer's Avatar
    01-07-2018, 06:54 PM
    Got a 2nd hand Lee .319 to lap out. I'd much prefer to have a mold that would include a sprue as opposed to an oversized flat spot on the front of the ball. But I'll make it work.
    11 replies | 289 view(s)
More Activity
About Good Cheer

Basic Information

About Good Cheer
Biography:
Been around long enough to know that you build a cattle chute with fences on the left and the right.
Location:
the Ark
Interests:
God, my woman, my tribe. And casting.
Occupation:
Since 1865

Statistics


Total Posts
Total Posts
2,698
Posts Per Day
0.99
General Information
Last Activity
Today 05:23 PM
Join Date
07-25-2010
Referrals
0

1 Friend

  1. Windwalker 45acp Windwalker 45acp is offline

    Boolit Master

    Windwalker 45acp
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check