Inline FabricationStainLess Steel MediaGraf & SonsTitan Reloading
MidSouth Shooters SupplyADvertise hereLee PrecisionRotoMetals2

  • Good Cheer's Avatar
    01-16-2018, 10:07 AM
    My catchers tend to be temporary constructs fabbed from castaway materials. If a sample needs to be recovered for examination something gets cobbled together like milk jugs of water backed by either soaked bundles of waste paper, shredded paper or...
    23 replies | 1470 view(s)
  • Good Cheer's Avatar
    01-16-2018, 07:03 AM
    I use a 9/16" gasket punch. How well your wads work will depend some on what you make them out of, how deep the rifling is, dry or lubed or soaked, all that jazz. Something I've tried is that spongy paper stuff that egg cartons are made of....
    4 replies | 171 view(s)
  • Good Cheer's Avatar
    01-14-2018, 07:13 PM
    Just put the letter in the envelope urging them to produce the steel receiver in .41 Magnum.
    35 replies | 2730 view(s)
  • Good Cheer's Avatar
    01-13-2018, 07:10 PM
    Well, what I been thinking is that when I get on out there distance wise the small differences will be magnified just like with any reloads. And that the flinter flash hole is large enough to produce substantial back flow which will not behave in...
    9 replies | 349 view(s)
  • Good Cheer's Avatar
    01-13-2018, 03:59 PM
    Hey there. Just asked 'cause I'm working towards getting a fast twist flinter working. I'm anticipating variations in elevation due to irregular back flow. But puffs in the puddin' so we'll see. And my new glasses should be in next week so maybe I...
    9 replies | 349 view(s)
  • Good Cheer's Avatar
    01-13-2018, 07:25 AM
    Are you seeing any significant vertical stringing at longer ranges?
    9 replies | 349 view(s)
  • Good Cheer's Avatar
    01-11-2018, 10:11 AM
    Has anyone concocted a specialty boolit / over all length loading to provide an improvement in .45 accuracy with the Judge type revolvers? A cousin has purchased one and it's got me wondering what would work better. Extended brass and hollow...
    25 replies | 585 view(s)
  • Good Cheer's Avatar
    01-09-2018, 04:15 PM
    To each his own. For a cast bullet deer rifle I designed for accuracy and excess power for 200 yards, my personal shooting accuracy limitation in the field. Turned out I never dropped one past 130.
    100 replies | 3067 view(s)
  • Good Cheer's Avatar
    01-09-2018, 11:35 AM
    I've tried various combinations trying to get Green Mountain .40 barrels to shoot other than round ball, with varying degrees of success. Lubed lead, paper patched, more powder, less powder... Getting consistent enough results just never happened:...
    6 replies | 191 view(s)
  • Good Cheer's Avatar
    01-08-2018, 10:08 PM
    Oh my, that sounds like a paper patch waiting to happen!
    14 replies | 368 view(s)
  • Good Cheer's Avatar
    01-08-2018, 09:55 PM
    On small diameters the flat moving a little bit towards the center rather than being tangential makes for an oddly flying projectile. In a percussion revolver maybe it wouldn't matter? I'd rather smoosh a sprue under the plunger.
    11 replies | 269 view(s)
  • Good Cheer's Avatar
    01-07-2018, 08:34 PM
    What's the biggest diameter boolits you can chamber in your 25-35?
    2 replies | 126 view(s)
  • Good Cheer's Avatar
    01-07-2018, 06:54 PM
    Got a 2nd hand Lee .319 to lap out. I'd much prefer to have a mold that would include a sprue as opposed to an oversized flat spot on the front of the ball. But I'll make it work.
    11 replies | 269 view(s)
  • Good Cheer's Avatar
    01-05-2018, 10:55 PM
    10-15 years ago I tried it in an Armisport 1842 (.69 rifled). Every third shot I had to pull the nipple and pick the stuff out of the ignition passage to get it go off. For whatever reason the geometry, the lube and the burned powder always worked...
    12 replies | 414 view(s)
  • Good Cheer's Avatar
    01-05-2018, 04:02 PM
    Ah ha. Thanks for the reminder. Driving into town this morning, discussed with the better 2/3's that I needed to touch base with them about when the .41's might be.
    35 replies | 2730 view(s)
  • Good Cheer's Avatar
    01-03-2018, 08:18 AM
    About recoil, here's some partly useful numbers from a 32" flint rifle with GOEX and .60 round ball. 80 grains FFg 1314FPS. 120 grains FFg 1533FPS.
    12 replies | 346 view(s)
  • Good Cheer's Avatar
    12-31-2017, 06:49 PM
    Well, just thinking out loud but if it's a brass mold then maybe what you really need is a barrel to shoot the boolits in. :happy dance:
    9 replies | 459 view(s)
  • Good Cheer's Avatar
    12-31-2017, 10:03 AM
    Maybe the blunderbuss would launch tennis balls across the yard? That could be some fun competition while the barbecue is getting ready.
    17 replies | 951 view(s)
  • Good Cheer's Avatar
    12-30-2017, 09:27 PM
    Always wanted to try the 375H&H with paper patched black loads because of hearing good reports. But what I have is a .38 Long Cox (375x45-70) so that'll do.
    13 replies | 372 view(s)
More Activity
About Good Cheer

Basic Information

About Good Cheer
Biography:
Been around long enough to know that you build a cattle chute with fences on the left and the right.
Location:
the Ark
Interests:
God, my woman, my tribe. And casting.
Occupation:
Since 1865

Statistics


Total Posts
Total Posts
2,693
Posts Per Day
0.99
General Information
Last Activity
Yesterday 08:44 PM
Join Date
07-25-2010
Referrals
0

1 Friend

  1. Windwalker 45acp Windwalker 45acp is offline

    Boolit Master

    Windwalker 45acp
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check