Graf & SonsLee PrecisionTitan ReloadingStainLess Steel Media
ADvertise hereInline FabricationRotoMetals2

Tab Content
  • mwhite49's Avatar
    Today, 03:22 PM
    mwhite49 replied to a thread M1A or Garand??? in Military Rifles
    And if Colorado goes with the insane mag ban it should not effect the Garrard. And they already make a 3 or 5 round clip too.
    13 replies | 102 view(s)
  • mwhite49's Avatar
    Today, 01:45 PM
    mwhite49 replied to a thread Your Health in Our Town
    I had to hold that towel or a pillow on my stomach so it would not hurt when i coughed. I gained about 10 lbs in water, 5 of which went into my scrotum. Doc never warned me about that. Scared the hell out of me. It went down after a couple of...
    7 replies | 260 view(s)
  • mwhite49's Avatar
    Today, 12:51 PM
    Thanks, i hope I'm lucky and pick one up for under 200.00.
    6 replies | 228 view(s)
  • mwhite49's Avatar
    Yesterday, 01:44 PM
    The one on ebay will sell for retail i bet. On sale now is 274.00 the cheapest ive seen.
    6 replies | 228 view(s)
  • mwhite49's Avatar
    11-16-2017, 09:34 PM
    I'm looking for an older redding t7 press. I could care less about color or amount of paint, as long as the price is LOW. And the ram goes up and down. Cash or trade is fine as i have items that will be going here soon.
    6 replies | 228 view(s)
  • mwhite49's Avatar
    11-16-2017, 12:26 AM
    I'm a pretty good machinist but no machine. But if i had one i would build a beefier Coax press with all kinds of clearance. I just like that design. I alsk like turret presses and have a nice all american. Maybe someday I'll get lucky and find a...
    35 replies | 960 view(s)
  • mwhite49's Avatar
    11-15-2017, 11:45 PM
    mwhite49 started a thread Your Health in Our Town
    I want to share a little known and not understood medi al issue that could save your life. Late last year i was diagnosed with a blocked lower Aorta was almost 100%. My doctor by chance decided to ask for a CAT SCAN WITH CONTRAST. That showed the...
    7 replies | 260 view(s)
  • mwhite49's Avatar
    11-15-2017, 10:33 PM
    mwhite49 added 2 photo(s) to album Health
  • mwhite49's Avatar
    11-15-2017, 10:29 PM
    mwhite49 created an album Health
  • mwhite49's Avatar
    11-15-2017, 09:19 AM
    Hey Lubedude, how does tbe Texan compare to the Hollywood turret press?
    35 replies | 960 view(s)
  • mwhite49's Avatar
    11-13-2017, 11:54 PM
    Redding T7 are very nice. Thanks to all for thd comments. I love my rockchucker. It's old but in good condition. I have 2 Bonanza coax presses. And a Dillon 550. Redding t7 is something I have been looking at.
    35 replies | 960 view(s)
  • mwhite49's Avatar
    11-11-2017, 08:55 PM
    The last one on ebay sold for 199.50 on 8-30-17
    35 replies | 960 view(s)
  • mwhite49's Avatar
    11-11-2017, 08:21 PM
    I have been looking for a Bair or Pacific D press. What I like is the fact that the whole opening is facing forward with no press sides in the way. I missed one on ebay awhile back. These in the Bair mofel sold for a higher price thsn the Bonanza...
    35 replies | 960 view(s)
  • mwhite49's Avatar
    11-10-2017, 06:01 PM
    Check auction houses.
    30 replies | 110 view(s)
  • mwhite49's Avatar
    11-02-2017, 05:52 AM
    I would like to add a case feeder to my 550 and dillon is sling them. But they sure look over complicated. They should have used a Hulme design and kept it simple.
    99 replies | 44835 view(s)
  • mwhite49's Avatar
    10-22-2017, 08:56 PM
    I need the following conversions, 32-20 and 45 LC. THANKS
    0 replies | 116 view(s)
  • mwhite49's Avatar
    10-21-2017, 11:21 PM
    I'll take the .223. Thanks Mike White
    7 replies | 93 view(s)
  • mwhite49's Avatar
    10-20-2017, 07:05 PM
    I'm in need of a complete conversion for 32 20 and 45lc and a y funnel if you have any of these. Thanks Mike White
    7 replies | 93 view(s)
  • mwhite49's Avatar
    10-19-2017, 09:34 PM
    I just paid 300 for mine. In fact just got it back from Dillon. For 67.00 they rebuilt it including the powder measure and primer system. Lots of parts are now new. You can't beat a Dillon.
    11 replies | 542 view(s)
  • mwhite49's Avatar
    10-19-2017, 09:15 PM
    I nust recieved my press bacm from Dillon. A very well spent $67.00. It shipped with a long list of repair items competed. Then as I'm mounting it to the quick change mount I started looking for all the little pieces. I screwed up and sent the...
    1 replies | 241 view(s)
No More Results
About mwhite49

Basic Information

About mwhite49
Biography:
Retired USN SEABEE
Location:
Camarillo Ca
Interests:
Reloading, target shooting, antique Colt SAA
Occupation:
Public Works construction inspection

Statistics


Total Posts
Total Posts
47
Posts Per Day
0.02
Albums
Total Albums
2
Total Photos
2
General Information
Last Activity
Today 03:30 PM
Current Activity
Viewing Forum Castpic of the Month
Join Date
07-23-2010
Referrals
0
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check