WidenersStainLess Steel MediaMidSouth Shooters SupplyTitan Reloading
Lee PrecisionInline FabricationRotoMetals2Graf & Sons

Tab Content
  • ian45662's Avatar
    09-15-2018, 10:15 AM
    Iím not worried about it. After going into the wet tumbler they are good as new. The residue from the black powder Iím using doesnít seem to eat the case. Now if I let them sit in the basement for a few days where itís damp they will corrode and...
    30 replies | 755 view(s)
  • ian45662's Avatar
    09-15-2018, 09:56 AM
    Nah. Sometimes I donít drop them into a bucket of water until the next day. When Iím at a match I just donít feel like de priming then and doing all that while I am trying to stay focused for the shoot. Sent from my iPhone using Tapatalk
    30 replies | 755 view(s)
  • ian45662's Avatar
    09-15-2018, 09:45 AM
    I do Anneal after each firing. Those were very early in my paper patch trials and for whatever reason they arnt as bad now but they still do it. Itís not real apparent when they are first fired but the next day is usually when they are black like...
    30 replies | 755 view(s)
  • ian45662's Avatar
    09-15-2018, 06:57 AM
    . So here are 2 cases. One was sized at the moth and the other was not. This darkening isnít apparent until sometime after the case has been fired. Sent from my iPhone using Tapatalk
    30 replies | 755 view(s)
  • ian45662's Avatar
    09-15-2018, 06:47 AM
    I get that little fowling at the end of my cases also. I am shooting pp out of a gg chamber but I have hardly any freebore. It used to bother my but I have gotten used to it Sent from my iPhone using Tapatalk
    30 replies | 755 view(s)
  • ian45662's Avatar
    09-14-2018, 09:18 AM
    Is that what the paper patchers do? Sent from my iPhone using Tapatalk
    14 replies | 371 view(s)
  • ian45662's Avatar
    08-28-2018, 05:32 AM
    I am also using a patch just shy of 7/8th and mine are also short of the ogive. I have yet to pull out any lead from the bore. Sent from my iPhone using Tapatalk
    88 replies | 3682 view(s)
  • ian45662's Avatar
    08-27-2018, 06:14 PM
    . My c sharps has no freebore. I have to seat grease groove bullets with no lube grooves showing. Here is a chamber cast of my rifle. Not sure when they did it but they have switched their Reamer design as I have seen some with freebore. Sent...
    8 replies | 569 view(s)
  • ian45662's Avatar
    08-24-2018, 03:49 PM
    . Flatsguide the mouth of your brass looks a lot like the mouth on mine after I run it through the Meacham. Sent from my iPhone using Tapatalk
    13 replies | 798 view(s)
  • ian45662's Avatar
    08-23-2018, 09:01 PM
    It was good to meet you Jim. You have got that 40 singing with those paper patch bullets. By rights you shoulda shot a master score on Saturday. To further drive your point home Jim I have never shot a master score with grease groove ammo. My rifle...
    61 replies | 3432 view(s)
No More Results
About ian45662

Basic Information

About ian45662
Location:
Portsmouth Ohio
Interests:
Shooting, Camping
Occupation:
Electrician

Statistics


Total Posts
Total Posts
220
Posts Per Day
0.07
General Information
Last Activity
Yesterday 12:13 PM
Join Date
07-10-2010
Referrals
0

1 Friend

  1. mstarling mstarling is offline

    Boolit Master

    mstarling
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check