ADvertise hereTitan ReloadingInline FabricationRotoMetals2
RepackboxLee PrecisionWidenersMidSouth Shooters Supply

Tab Content
  • catmandu's Avatar
    10-10-2019, 12:50 PM
    I have a bit set that I use every week, been using it for 20 years. Its a red box WFMC or Wadsworth mini super delux 52 bit set. Its my goto set before I look for a special fit. Very good quality. I see they are in amazon. Paul in WNY
    39 replies | 2196 view(s)
  • NSB's Avatar
    10-09-2019, 06:18 PM
    The bullet follows the rear sight. Just look at the aperture and see which way it moves when you turn it.
    5 replies | 475 view(s)
  • NSB's Avatar
    10-07-2019, 11:52 AM
    NSB replied to a thread Turning Down Rim Diameter in Leverguns
    I don't know how much brass you have for your gun, but I can tell you that you'll probably get a minimum of a dozen shots out of each case. I'd think even more, but I haven't loaded mine enough to answer that yet. These cases are like pistol...
    16 replies | 629 view(s)
  • NSB's Avatar
    10-02-2019, 10:59 PM
    Randy is correct. Lever guns, Sharps, High Walls, etc are all prone to POI changes from any variation in how they sit on the rest, pressure put on the gun while on the rest, and being pulled back into the shoulder. You can prove this to yourself by...
    19 replies | 783 view(s)
  • NSB's Avatar
    09-26-2019, 12:36 AM
    I believe galling is reduced when you do use different grades of stainless steel.It's caused when using the same stainless steel. FWIW, neither of my two Dan Wessons had any, I repeat ANY problems with failure to feed, fire, or eject. They operated...
    26 replies | 955 view(s)
  • NSB's Avatar
    09-23-2019, 07:22 PM
    I had two of them back when Dan Coonan was actually the owner of the company and producing the guns. I don't know how the new owners' (not so new anymore) quality is, but the originals were great. You do not have to shoot full power loads out of...
    26 replies | 955 view(s)
  • NSB's Avatar
    09-22-2019, 10:47 PM
    NSB replied to a thread Name brand wads in Casting for Shotguns
    I've shot countless thousands of Claybuster wads without a problem. Probably into a couple hundred thousand by now. I haven't noticed any difference between them and the "brand name" wads. Not any difference in score either.
    16 replies | 565 view(s)
  • NSB's Avatar
    09-18-2019, 11:49 AM
    You're right, I just saw "Sharps" and my mind went to the wrong gun. When I see Sharps I head right to the 1874 side hammer.
    32 replies | 1098 view(s)
  • NSB's Avatar
    09-18-2019, 11:45 AM
    It isn't going to get worse unless you fire another round on top of a squib stuck in the barrel (probably what happened to begin with). It's safe to shoot. It's just whatever you want to do about it. If it shoots good and if it were mine, I'd...
    31 replies | 1165 view(s)
  • NSB's Avatar
    09-18-2019, 09:47 AM
    Wrong.....you have to put the gun on half cock before opening the lever. If you don't do that, you'll break firing pins. That's not a secret, it's probably in your owners manual.
    32 replies | 1098 view(s)
  • NSB's Avatar
    09-17-2019, 10:50 AM
    Too much crimp. Too many people add a lot more crimp than is needed to do its job. Pretty much just take the flair off the brass and you're good.
    33 replies | 1137 view(s)
  • NSB's Avatar
    09-17-2019, 07:43 AM
    EXPERIENCE will show that it's where the bullet hits that kills. Neither cartridge is a long range cartridge....or shouldn't be. If you're making a choice on which to use, look at how well the gun shoots, how well you can shoot the gun, and don't...
    73 replies | 3643 view(s)
  • NSB's Avatar
    09-17-2019, 05:47 AM
    I've taken over fifty deer with the .357mag with just the handgun alone. Another nine or ten with a Marlin lever gun and a Low Wall. I have yet to lose even one deer with the .357mag and only lost one with the handgun and that was with a full power...
    73 replies | 3643 view(s)
No More Results
About NSB

Basic Information

About NSB
Biography:
Long time competition shooter
Location:
WNY
Interests:
Shooting, hunting, fishing
Occupation:
Retired engineer

Statistics


Total Posts
Total Posts
1,631
Posts Per Day
0.48
General Information
Last Activity
Yesterday 09:05 PM
Join Date
06-04-2010
Referrals
0

1 Friend

  1. catmandu catmandu is offline

    Boolit Buddy

    catmandu
Showing Friends 1 to 1 of 1
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check